GreenLake Administration
- Community Home
- >
- Storage
- >
- Legacy
- >
- Disk
- >
- HP-6000 sx-w SCSI disks
Disk
1848031
Members
2445
Online
104022
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Forums
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-17-2001 05:43 AM
09-17-2001 05:43 AM
HP-6000 sx-w SCSI disks
Hello all,
This is a bit of an odd question, but does anyone know if these units could power themselves off (aka trip their power somehow)?
The situation is I came this morning and the unit was off. No power issues and it's all under lock and key in a controled environment. There were some people in there over the weekend, but I don't think they would have been in that area.
So basically I'm wondering if something could have caused it to power off or if I should be looking more into who would have been near it.
Thanks,
Steve
This is a bit of an odd question, but does anyone know if these units could power themselves off (aka trip their power somehow)?
The situation is I came this morning and the unit was off. No power issues and it's all under lock and key in a controled environment. There were some people in there over the weekend, but I don't think they would have been in that area.
So basically I'm wondering if something could have caused it to power off or if I should be looking more into who would have been near it.
Thanks,
Steve
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-17-2001 05:51 AM
09-17-2001 05:51 AM
Re: HP-6000 sx-w SCSI disks
Hi, I was working with HP-9000 racked version, and was an issue with theses disks. If you remove the front pannel, when you put it in his place, is very easy to accidentaly push power button off.
Ask people that was this weekend working if they do that.
I don't know if these boxes have any temp alert that shut the power off or something similar. I don't think so.
Good Luck
Ask people that was this weekend working if they do that.
I don't know if these boxes have any temp alert that shut the power off or something similar. I don't think so.
Good Luck
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-17-2001 06:30 AM
09-17-2001 06:30 AM
Re: HP-6000 sx-w SCSI disks
My colleague is right, they are *extremely* easy to turn off accidentally. We they all off or just one? If one then a bad drive, if all then ask strenuously if any was even NEAR the drives. If it happens again, replace the power supply if it has one (you weren't too clear on the model #)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-17-2001 01:35 PM
09-17-2001 01:35 PM
Re: HP-6000 sx-w SCSI disks
Hello Steve,
One additional twist to add to the power off scenerios listed above.
Sometimes, upon installation of the front panel, the power button is pressed down enough to cause it to mechanically overcome the 'power off path' inside the switch assembly. At that point, only the friction between the white switch cap and the front panel facia keeps the switch from fully extending and shuting down the power supply. Then, at some future date/time, just a simple 'bump' or 'adjustment' of the front panel facia sets the shutdown into motion.
Good Luck,
Curt
One additional twist to add to the power off scenerios listed above.
Sometimes, upon installation of the front panel, the power button is pressed down enough to cause it to mechanically overcome the 'power off path' inside the switch assembly. At that point, only the friction between the white switch cap and the front panel facia keeps the switch from fully extending and shuting down the power supply. Then, at some future date/time, just a simple 'bump' or 'adjustment' of the front panel facia sets the shutdown into motion.
Good Luck,
Curt
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
Company
Events and news
Customer resources
© Copyright 2026 Hewlett Packard Enterprise Development LP