change threshold for SSD raw space allocation

[cgeorge0147]

Hey, We are receive alerts that 3PAR StoreServ SSD Raw Space Allocation is above 86%, I would like to change this sow we don't get an alert.

Where can I change this type of threshold?

[Satish04]

Hi cgeorge0147,

Please refer to the below videos to change the RawSpace Aletra on your HPE 3PAR StoreServ Storage.

URL - https://support.hpe.com/hpesc/public/videoDisplay?videoId=vtc00030433en_us

URL - https://support.hpe.com/hpesc/public/videoDisplay?videoId=vtc00030383en_us

Hope this helps.

Regards,
Satish

[Moderator note: Edited the post and updated the correct links]

[cgeorge0147]

Hi, thnx, I can't op this url's

[Satish04]

Hi cgeorge0147,

Sorry, by mistake I gave the wrong URLs, please find the correct URLs below.

URL - https://support.hpe.com/hpesc/public/videoDisplay?videoId=vtc00030433en_us

URL - https://support.hpe.com/hpesc/public/videoDisplay?videoId=vtc00030383en_us

Hope this helps.

Regards,
Satish

[cgeorge0147]

Hmm, still no luck

Video not available

Please check the Video ID or your account permissions.

Note:
Customers and HPE Partners: login using an HPE Passport account associated with your company email address
Employees: login via HPE employee sign-in

[Satish04]

Hi cgeorge0147,

Please follow the below steps to change the RawSpaceAlerts using CLI or HPE SSMC:

Using CLI::

1. Login to Putty using the IP address of the HPE 3PAR StoreServ Storage.

2. Run the command “showsys -param” to see the existing Raw Space Alert parameters and their values.

3. Here, you can see the Raw Space Alerts for FC, NL and SSD drive types.

4. To set the Raw Space Alert for any drive type, run the command “setsys RawSpaceAlert<drive type> <value>”. In this instance we are setting the Raw Space Alert for FC.

5. To verify that the value is set, run the command “showsys -param”.

6. Now, you see the Raw Space Alert is set for FC drive type.

Using HPE SSMC::
1. Login to the HPE SSMC.

2. Go to the main menu.

3. Select “Systems” under storage systems.

4. All the connected Storage systems will be listed, select the storage system to edit the custom raw space alerts.

5. You will see the system details. Go to the “Actions” menu at the top right corner and click “Edit”.

6. Under the “System Parameters” pane, use the toggle to enable the alert for the drive type to specify the value. By default, these alerts are disabled.

7. Click “Ok” to apply the changes. This may take a few seconds.

8. Go to the Overview dropdown menu.

9. Select “Settings”.

10. Now, you see the changes are updated under the system parameters pane.

Hope this helps.

Regards,
Satish

[cgeorge0147]

Hi,, thnx for you replay

what value should I enter? The amount of GB left over before receive a notifications?

[Satish04]

Hi cgeorge0147,

You need to set the RawSpaceAlert based on your environment and requirements.

For example, If you set the RawSpaceAlert to 85%, you will get the alerts when it reaches 85%.

If you set it to zero, you will not get the alert.

Note: The capacity thresholds for the user-defined Raw Space Alerts can be from 10 GiB to 100,000 GiB for each drive type.

Hope this helps.

Regards,
Satish

[cgeorge0147]

ok, but I have to put in an amount in GB? How much do I put in then?

[AnilKT]

Hi cgeorge0147,

You just need the give the value in Percentage (%), not  in GB. If you want to disable the Raw Space Alerts, give the percentage as “Zero (0)’’.

The command to set the Raw Space Alerts is “setsys RawSpaceAlert<drive type> <value>”.

In your case the command can be “setsys RawSpaceAlert<SSD> <value>”

Note: If you want to disable the RAW space alerts, please give the value as 0 (Zero).

To verify the new Raw Space Alerts set, run the command “showsys -param”

Hope this helps.!

Regards

Anil