HP 5406zl Parity Error

[Chris32]

Hi folks,

I have recently noticed this error cropping up in my logs routinely. I'm slightly confused as I don't have a module K so I'm not sure what its referring to

00907 IpAddrMgr: ST1-CMDR: Module K BMP TCAM parity recovery
0x80008e74 0x00000000

Could it be referencing the supervisor?

Thanks for any help

Chris

[akg7]

Hello @Chris32,

What is the software version device?

Can you run below comamnds:

show version
show module

Thanks!

[Chris32]

Hi @akg7 

HQK--Core# show version

Image stamp: /ws/swbuildm/rel_ukiah_qaoff/code/build/bom(swbuildm_rel_ukiah_qaoff_rel_ukiah)
Jul 21 2017 14:42:33
KB.16.04.0008
442
Boot Image: Primary

Boot ROM Version: KB.16.01.0006
Active Boot ROM: Primary

show modules

Allow V2 Modules: No

Core Mod
Slot Module Description Serial Number Status Dump Ver
----- -------------------------------------- -------------- -------- ----- ---
1/MM1 HP J9827A Management Module 5400Rzl2 SG78G4C3PS Active YES 1
1/MM2 HP J9827A Management Module 5400Rzl2 Offline YES 1

1/A HP J9993A 8p 1G/10GbE SFP+ v3 zl2 Mod SG79GPK021 Up YES 3
1/B HP J9993A 8p 1G/10GbE SFP+ v3 zl2 Mod SG79GPK01Z Up YES 3
1/C HP J9986A 24p 10/100/1000BASE-T PoE... SG76GPB79W Up YES 3
1/D HP J9990A 20p PoE+ / 4p SFP+ v3 zl2... SG77GPG0VP Up YES 3
1/E HP J9993A 8p 1G/10GbE SFP+ v3 zl2 Mod SG03GPK19X Up YES 3

2/MM1 HP J9827A Management Module 5400Rzl2 SG78G4C3YB Active YES 1
2/MM2 HP J9827A Management Module 5400Rzl2 Offline YES 1

2/A HP J9993A 8p 1G/10GbE SFP+ v3 zl2 Mod SG79GPK0F5 Up YES 3
2/B HP J9993A 8p 1G/10GbE SFP+ v3 zl2 Mod SG79GPK02G Up YES 3
2/C HP J9989A 12p PoE+ / 12p 1GbE SFP v... SG76GPF05T Up YES 3
2/E HP J9993A 8p 1G/10GbE SFP+ v3 zl2 Mod Up YES 3

[akg7]

Hello @Chris32,

The Event Log Message Reference Guide gives the following explanation:

# 907
Message <slot> <memory location> <table type> parity recovery <table entry>
Severity warning
Description There has been a successful recovery from a parity error. RMON_IPADDRMGR_PARITY_ERROR_RECOVERY

Refer below link:

https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-c03246015

Device is running on quie old software version so I will advise you to upgrade the switch to latest software version.

What is the reason for Management Module 2 is offline?

1/MM2 HP J9827A Management Module 5400Rzl2 Offline YES 1

Thanks!

[parnassus]

---

@akg7 wrote: What is the reason for Management Module 2 is offline?

---

That's a VSF.

Secondary MM on each chassis of a VSF Cluster is automatically set offline by enabling the VSF configuration.

Edit:

Note 1: the Thread title is misleading (OP refers to HP ProCurve 5400 zl but he is really dealing with a pair of Aruba 5400R zl2, as command outputs report).

Note 2: IIRC KB.16.04.0008 was mid 2017, it's time to update, go to KB.16.11.0002.