Mitel and VLANs on 2520-24 POE

[Switches_1]

We are installing Mitel VoiP and decided to change to POE switches. I have 4 vlans
default vlan 1
vlan 20 Engineering 192.168.20.0/24 g/w 192.168.20.1
vlan 21 Management 192.168.21.0/24 g/w 192.168.21.254
vlan 99 VOIP 192.168.99.0/24 g/w 192.168.99.254

The dhcp server issues just fine for management and engineering. The goal is to have engineering untagged, and voip tagged on each end-user port.

All the mac's are entered into the Mitel 5240 for each endpoint. When I connect a phone(endpoint) to the switch port, it stays in dhcp discovery, never gets an ip, with vlan 99 set to the phone.
If I take out the vlan 99, then the phone gets a ip from vlan 20.

Anyone know if I have to set the port up as a trunk or just tagged and untagged.

P.S. This thread has been moved from Switches, Hubs, Modems (Legacy ITRC forum) to ProCurve / ProVision-Based. - Hp Forum Moderator

[Sietze Reitsma]

For vlan 99 you need to add the function 'voice' to enable LLDP-MED. Phone wil recognize/configure itself automatically in the right vlan.

#vlan 99 voice
' tag all ports where you want to connect a phone, for example port 1 to 12
(vlan 99)# tagged 1-12

[Switches_1]

hanks, I added that with no change.
Here is the config and layout
DHCP server 192.168.20.3
scope 192.168.20.0/24 vlan20
scope 192.168.21.0/24 vlan21
scope 192.168.22.0/24 vlan22
scope 192.168.99.0/24 vlan99

VLAN99 is for VoiP

The Mitel is on port 19 of the layer-3 switch. We are using the external power brick for now instead of the POE switches, just testing on the core switch.

If I set the phone port 10 to untagged 99 it works great, gets a 192.168.99.xx IP, except there is no option for the PC on vlan21 or vlan20.



; J9085A Configuration Editor; Created on release #R.11.30

hostname "CORE Switch 2610-24"
snmp-server contact "Tom"
snmp-server location "Server Room"
interface 1
name "To Firewall"
exit
interface 10
name "Test Phone"
exit
interface 11
name "WireShark"
exit
interface 19
name "Mitel 5200"
exit
ip default-gateway 192.168.20.1
ip routing
snmp-server community "public" Unrestricted
snmp-server host 192.168.20.29 "public"
snmp-server host 192.168.20.9 "public"
vlan 1
name "DEFAULT_VLAN"
untagged 1-10,12-18,20-28
ip address 192.168.20.1 255.255.255.0
no untagged 11,19
exit
vlan 21
name "Engineering"
ip address 192.168.21.254 255.255.255.0
ip helper-address 192.168.20.3
tagged 1,9,24-26
exit
vlan 101
name "DCS-101"
ip address 192.168.101.254 255.255.255.0
tagged 9,24,26
exit
vlan 99
name "VOIP"
untagged 19
ip address 192.168.99.254 255.255.255.0
ip helper-address 192.168.20.3
tagged 1,3-12,24-26
voice
exit
vlan 114
name "iHawks"
ip address 172.18.114.254 255.255.0.0
tagged 10,26
exit
vlan 100
name "DCS-100"
ip address 192.168.100.254 255.255.255.0
tagged 10,25
exit
vlan 22
name "Management"
ip address 192.168.22.254 255.255.255.0
ip helper-address 192.168.20.3
tagged 1,9,24-26
exit
fault-finder bad-driver sensitivity high
fault-finder bad-transceiver sensitivity high
fault-finder bad-cable sensitivity high
fault-finder too-long-cable sensitivity high
fault-finder over-bandwidth sensitivity high
fault-finder broadcast-storm sensitivity high
fault-finder loss-of-link sensitivity high
fault-finder duplex-mismatch-HDx sensitivity high
fault-finder duplex-mismatch-FDx sensitivity high
ip route 0.0.0.0 0.0.0.0 192.168.20.254
password manager
password operator

[Darren Etheridge_2]

Here are my notes for setting up a POE switch for our mitel systems:


Non gui

Config
Vlan 1 name Data (rename vlan 1 to Data
Vlan 101 Voice (Create vlan 101)
Vlan 101 name voice (rename vlan 101 to voice)
Vlan 101 (get into vlan config menu)
Tag a1-b24 (or tag 1-24) (tagging all ports)
Write mem