Route to IP address missing

[robbyde]

Hi All,

I'm new to HP's and networking generally but here's my problem:

My PC is sat on a vlan ID 3111 which means I get a IP address in the 192.168.111.* range.

There's a switch thats connected to core switch that has a IP of 10.0.0.54 (HP ProCurve 2824) that I can not connect to by web or telnet but servers on the switch such as 10.0.0.10 I can connect to by all the normal means.

I can not ping the switch and a tracert fails.

If I do a route print I get this:

IPv4 Route Table
===========================================================================
Active Routes:
Network Destination        Netmask          Gateway       Interface  Metric
          0.0.0.0          0.0.0.0  192.168.111.254    192.168.111.1     10
        127.0.0.0        255.0.0.0         On-link         127.0.0.1    306
        127.0.0.1  255.255.255.255         On-link         127.0.0.1    306
  127.255.255.255  255.255.255.255         On-link         127.0.0.1    306
      169.254.0.0      255.255.0.0         On-link     169.254.86.18    276
      169.254.0.0      255.255.0.0         On-link    169.254.37.179    276
   169.254.37.179  255.255.255.255         On-link    169.254.37.179    276
    169.254.86.18  255.255.255.255         On-link     169.254.86.18    276
  169.254.255.255  255.255.255.255         On-link     169.254.86.18    276
  169.254.255.255  255.255.255.255         On-link    169.254.37.179    276
    192.168.111.0    255.255.255.0         On-link     192.168.111.1    266
    192.168.111.1  255.255.255.255         On-link     192.168.111.1    266
  192.168.111.255  255.255.255.255         On-link     192.168.111.1    266
        224.0.0.0        240.0.0.0         On-link         127.0.0.1    306
        224.0.0.0        240.0.0.0         On-link     192.168.111.1    266
        224.0.0.0        240.0.0.0         On-link    169.254.37.179    276
        224.0.0.0        240.0.0.0         On-link     169.254.86.18    276
  255.255.255.255  255.255.255.255         On-link         127.0.0.1    306
  255.255.255.255  255.255.255.255         On-link     192.168.111.1    266
  255.255.255.255  255.255.255.255         On-link    169.254.37.179    276
  255.255.255.255  255.255.255.255         On-link     169.254.86.18    276
===========================================================================

If I connect to a server on 10.0.0.* then I can connect to the switch, so its something about my subnet or vlan or something?

Other switches on 10.0.0.* are fine such as my core switch.

Any ideas?

P.S. This thread has been moved from  Switches, Hubs, Modems (Legacy ITRC forum) to ProCurve / ProVision-Based. -HP Forum Moderator

[Vince_Whirlwind]

What is the default gateway on the 10.0.0.54 switch?

[robbyde]

Goes to 10.0.0.76 255.0.0.0 which is our core switch.

[Vince_Whirlwind]

And the default gateway on 10.0.0.10 is what?

[Vince_Whirlwind]

Can you connect to 10.0.0.54 from a PC on the 10. network?