Multi-path RedHat AS4 and EVA8000

[Yermek Bissenbayev]

Dear All,
Please help to enable multi-path on RedHat AS4.
The equipment:
1) EVA8000 2C6D.
2) Dell PowerEge 2600 with OS Linux RedHAt AS4 Kernel: 2.6.9-5.ELsmp; 2-FCA2214 (driver hp_qla2x00src 8.00.02p11 Release: 24).
3) SAN

100GB from EVA presented to a Linux server.

Bellow full logs:
#messages
Apr 17 11:30:41 keglin kernel: QLogic Fibre Channel HBA Driver
Apr 17 11:30:41 keglin kernel: ACPI: PCI interrupt 0000:05:04.0[A] -> GSI 72 (level, low) -> IRQ 193
Apr 17 11:30:41 keglin kernel: qla2300 0000:05:04.0: Found an ISP2312, irq 193, iobase 0xf8816000
Apr 17 11:30:41 keglin kernel: qla2300 0000:05:04.0: Configuring PCI space...
Apr 17 11:30:41 keglin kernel: qla2300 0000:05:04.0: Configure NVRAM parameters...
Apr 17 11:30:41 keglin kernel: qla2300 0000:05:04.0: Verifying loaded RISC code...
Apr 17 11:30:41 keglin kernel: qla2300 0000:05:04.0: LIP reset occured (f7f7).
Apr 17 11:30:41 keglin kernel: qla2300 0000:05:04.0: Waiting for LIP to complete...
Apr 17 11:30:41 keglin kernel: qla2300 0000:05:04.0: LOOP UP detected (2 Gbps).
Apr 17 11:30:41 keglin kernel: qla2300 0000:05:04.0: Topology - (F_Port), Host Loop address 0xffff
Apr 17 11:30:41 keglin kernel: scsi1 : qla2xxx
Apr 17 11:30:41 keglin kernel: qla2300 0000:05:04.0:
Apr 17 11:30:41 keglin kernel: QLogic Fibre Channel HBA Driver: 8.00.02p11
Apr 17 11:30:41 keglin kernel: QLogic QLA2340 -
Apr 17 11:30:41 keglin kernel: ISP2312: PCI-X (100 MHz) @ 0000:05:04.0 hdma+, host#=1, fw=3.03.11 IPX
Apr 17 11:30:41 keglin kernel: scsi: unknown device type 12
Apr 17 11:30:41 keglin kernel: Vendor: HP Model: HSV210 Rev: 5031
Apr 17 11:30:41 keglin kernel: Type: RAID ANSI SCSI revision: 05
Apr 17 11:30:41 keglin kernel: qla2300 0000:05:04.0: scsi(1:0:0:0): Enabled tagged queuing, queue depth 16.
Apr 17 11:30:41 keglin kernel: Vendor: HP Model: HSV210 Rev: 5031
Apr 17 11:30:41 keglin kernel: Type: Direct-Access ANSI SCSI revision: 05
Apr 17 11:30:41 keglin kernel: qla2300 0000:05:04.0: scsi(1:0:0:1): Enabled tagged queuing, queue depth 16.
Apr 17 11:30:41 keglin kernel: SCSI device sdb: 209715200 512-byte hdwr sectors (107374 MB)
Apr 17 11:30:41 keglin kernel: SCSI device sdb: drive cache: write through
Apr 17 11:30:41 keglin kernel: sdb: unknown partition table
Apr 17 11:30:41 keglin kernel: Attached scsi disk sdb at scsi1, channel 0, id 0, lun 1
Apr 17 11:30:41 keglin kernel: scsi: unknown device type 12
Apr 17 11:30:41 keglin kernel: Vendor: HP Model: HSV210 Rev: 5031
Apr 17 11:30:41 keglin kernel: Type: RAID ANSI SCSI revision: 05
Apr 17 11:30:41 keglin kernel: qla2300 0000:05:04.0: scsi(1:0:1:0): Enabled tagged queuing, queue depth 16.
Apr 17 11:30:41 keglin kernel: Vendor: HP Model: HSV210 Rev: 5031
Apr 17 11:30:41 keglin kernel: Type: Direct-Access ANSI SCSI revision: 05
Apr 17 11:30:41 keglin kernel: qla2300 0000:05:04.0: scsi(1:0:1:1): Enabled tagged queuing, queue depth 16.
Apr 17 11:30:41 keglin kernel: SCSI device sdc: 209715200 512-byte hdwr sectors (107374 MB)
Apr 17 11:30:41 keglin kernel: SCSI device sdc: drive cache: write through
Apr 17 11:30:41 keglin kernel: sdc: unknown partition table
Apr 17 11:30:41 keglin kernel: Attached scsi disk sdc at scsi1, channel 0, id 1, lun 1
Apr 17 11:30:41 keglin kernel: scsi: unknown device type 12
Apr 17 11:30:41 keglin kernel: Vendor: HP Model: HSV210 Rev: 5031
Apr 17 11:30:41 keglin kernel: Type: RAID ANSI SCSI revision: 05
Apr 17 11:30:41 keglin kernel: qla2300 0000:05:04.0: scsi(1:0:2:0): Enabled tagged queuing, queue depth 16.
Apr 17 11:30:41 keglin kernel: Vendor: HP Model: HSV210 Rev: 5031
Apr 17 11:30:41 keglin kernel: Type: Direct-Access ANSI SCSI revision: 05
Apr 17 11:30:41 keglin kernel: qla2300 0000:05:04.0: scsi(1:0:2:1): Enabled tagged queuing, queue depth 16.
Apr 17 11:30:41 keglin rpcidmapd: rpc.idmapd startup succeeded
Apr 17 11:30:41 keglin kernel: SCSI device sdd: 209715200 512-byte hdwr sectors (107374 MB)
Apr 17 11:30:41 keglin kernel: SCSI device sdd: drive cache: write through
Apr 17 11:30:41 keglin kernel: sdd: unknown partition table
Apr 17 11:30:41 keglin kernel: Attached scsi disk sdd at scsi1, channel 0, id 2, lun 1
Apr 17 11:30:41 keglin kernel: scsi: unknown device type 12
Apr 17 11:30:41 keglin kernel: Vendor: HP Model: HSV210 Rev: 5031
Apr 17 11:30:41 keglin kernel: Type: RAID ANSI SCSI revision: 05
Apr 17 11:30:41 keglin kernel: qla2300 0000:05:04.0: scsi(1:0:3:0): Enabled tagged queuing, queue depth 16.
Apr 17 11:30:41 keglin kernel: Vendor: HP Model: HSV210 Rev: 5031
Apr 17 11:30:41 keglin kernel: Type: Direct-Access ANSI SCSI revision: 05
Apr 17 11:30:41 keglin kernel: qla2300 0000:05:04.0: scsi(1:0:3:1): Enabled tagged queuing, queue depth 16.
Apr 17 11:30:41 keglin kernel: SCSI device sde: 209715200 512-byte hdwr sectors (107374 MB)
Apr 17 11:30:41 keglin kernel: SCSI device sde: drive cache: write through
Apr 17 11:30:41 keglin kernel: sde: unknown partition table
Apr 17 11:30:41 keglin kernel: Attached scsi disk sde at scsi1, channel 0, id 3, lun 1
Apr 17 11:30:41 keglin kernel: ACPI: PCI interrupt 0000:06:03.0[A] -> GSI 80 (level, low) -> IRQ 201
Apr 17 11:30:41 keglin kernel: qla2300 0000:06:03.0: Found an ISP2312, irq 201, iobase 0xf8818000
Apr 17 11:30:41 keglin kernel: qla2300 0000:06:03.0: Configuring PCI space...
Apr 17 11:30:41 keglin kernel: qla2300 0000:06:03.0: Configure NVRAM parameters...
Apr 17 11:30:41 keglin kernel: qla2300 0000:06:03.0: Verifying loaded RISC code...
Apr 17 11:30:41 keglin kernel: qla2300 0000:06:03.0: LIP reset occured (f800).
Apr 17 11:30:41 keglin kernel: qla2300 0000:06:03.0: Waiting for LIP to complete...
Apr 17 11:30:41 keglin kernel: qla2300 0000:06:03.0: LOOP UP detected (2 Gbps).
Apr 17 11:30:41 keglin kernel: qla2300 0000:06:03.0: Topology - (F_Port), Host Loop address 0xffff
Apr 17 11:30:41 keglin kernel: scsi2 : qla2xxx
Apr 17 11:30:41 keglin kernel: qla2300 0000:06:03.0:
Apr 17 11:30:41 keglin kernel: QLogic Fibre Channel HBA Driver: 8.00.02p11
Apr 17 11:30:41 keglin kernel: QLogic QLA2340 -
Apr 17 11:30:41 keglin kernel: ISP2312: PCI-X (133 MHz) @ 0000:06:03.0 hdma+, host#=2, fw=3.03.11 IPX
Apr 17 11:30:41 keglin kernel: scsi: unknown device type 12
Apr 17 11:30:41 keglin kernel: Vendor: HP Model: HSV210 Rev: 5031
Apr 17 11:30:41 keglin kernel: Type: RAID ANSI SCSI revision: 05
Apr 17 11:30:41 keglin kernel: qla2300 0000:06:03.0: scsi(2:0:0:0): Enabled tagged queuing, queue depth 16.
Apr 17 11:30:41 keglin kernel: Vendor: HP Model: HSV210 Rev: 5031
Apr 17 11:30:41 keglin kernel: Type: Direct-Access ANSI SCSI revision: 05
Apr 17 11:30:41 keglin kernel: qla2300 0000:06:03.0: scsi(2:0:0:1): Enabled tagged queuing, queue depth 16.
Apr 17 11:30:41 keglin kernel: SCSI device sdf: 209715200 512-byte hdwr sectors (107374 MB)
Apr 17 11:30:41 keglin kernel: SCSI device sdf: drive cache: write through
Apr 17 11:30:41 keglin kernel: sdf: unknown partition table
Apr 17 11:30:41 keglin kernel: Attached scsi disk sdf at scsi2, channel 0, id 0, lun 1
Apr 17 11:30:41 keglin kernel: scsi: unknown device type 12
Apr 17 11:30:41 keglin kernel: Vendor: HP Model: HSV210 Rev: 5031
Apr 17 11:30:41 keglin kernel: Type: RAID ANSI SCSI revision: 05
Apr 17 11:30:41 keglin kernel: qla2300 0000:06:03.0: scsi(2:0:1:0): Enabled tagged queuing, queue depth 16.
Apr 17 11:30:41 keglin netfs: Mounting other filesystems: succeeded
Apr 17 11:30:41 keglin kernel: Vendor: HP Model: HSV210 Rev: 5031
Apr 17 11:30:41 keglin kernel: Type: Direct-Access ANSI SCSI revision: 05
Apr 17 11:30:41 keglin kernel: qla2300 0000:06:03.0: scsi(2:0:1:1): Enabled tagged queuing, queue depth 16.
Apr 17 11:30:41 keglin kernel: SCSI device sdg: 209715200 512-byte hdwr sectors (107374 MB)
Apr 17 11:30:41 keglin kernel: SCSI device sdg: drive cache: write through
Apr 17 11:30:41 keglin kernel: sdg: unknown partition table
Apr 17 11:30:41 keglin kernel: Attached scsi disk sdg at scsi2, channel 0, id 1, lun 1
Apr 17 11:30:41 keglin kernel: scsi: unknown device type 12
Apr 17 11:30:41 keglin kernel: Vendor: HP Model: HSV210 Rev: 5031
Apr 17 11:30:41 keglin kernel: Type: RAID ANSI SCSI revision: 05
Apr 17 11:30:41 keglin kernel: qla2300 0000:06:03.0: scsi(2:0:2:0): Enabled tagged queuing, queue depth 16.
Apr 17 11:30:41 keglin kernel: Vendor: HP Model: HSV210 Rev: 5031
Apr 17 11:30:41 keglin kernel: Type: Direct-Access ANSI SCSI revision: 05
Apr 17 11:30:41 keglin kernel: qla2300 0000:06:03.0: scsi(2:0:2:1): Enabled tagged queuing, queue depth 16.
Apr 17 11:30:41 keglin kernel: SCSI device sdh: 209715200 512-byte hdwr sectors (107374 MB)
Apr 17 11:30:41 keglin kernel: SCSI device sdh: drive cache: write through
Apr 17 11:30:41 keglin kernel: sdh: unknown partition table
Apr 17 11:30:41 keglin kernel: Attached scsi disk sdh at scsi2, channel 0, id 2, lun 1
Apr 17 11:30:41 keglin kernel: scsi: unknown device type 12
Apr 17 11:30:41 keglin kernel: Vendor: HP Model: HSV210 Rev: 5031
Apr 17 11:30:41 keglin kernel: Type: RAID ANSI SCSI revision: 05
Apr 17 11:30:41 keglin kernel: qla2300 0000:06:03.0: scsi(2:0:3:0): Enabled tagged queuing, queue depth 16.
Apr 17 11:30:41 keglin kernel: Vendor: HP Model: HSV210 Rev: 5031
Apr 17 11:30:41 keglin kernel: Type: Direct-Access ANSI SCSI revision: 05
Apr 17 11:30:41 keglin kernel: qla2300 0000:06:03.0: scsi(2:0:3:1): Enabled tagged queuing, queue depth 16.
Apr 17 11:30:41 keglin kernel: SCSI device sdi: 209715200 512-byte hdwr sectors (107374 MB)
Apr 17 11:30:41 keglin kernel: SCSI device sdi: drive cache: write through
Apr 17 11:30:41 keglin kernel: sdi: unknown partition table
Apr 17 11:30:41 keglin kernel: Attached scsi disk sdi at scsi2, channel 0, id 3, lun 1

#proc_qla
::::::::::::::
/proc/scsi/qla2xxx/1
::::::::::::::
QLogic PCI to Fibre Channel Host Adapter for QLA2340:
Firmware version 3.03.02 IPX, Driver version 8.00.00b21-k
Entry address = f8861000
ISP: ISP2312, Serial# C25368
Request Queue = 0x37640000, Response Queue = 0x37620000
Request Queue count = 2048, Response Queue count = 512
Total number of active commands = 0
Total number of interrupts = 10131
Device queue depth = 0x20
Number of free request entries = 1672
Number of mailbox timeouts = 0
Number of ISP aborts = 0
Number of loop resyncs = 0
Number of retries for empty slots = 0
Number of reqs in pending_q= 0, retry_q= 0, done_q= 0, scsi_retry_q= 0
Host adapter:loop state = , flags = 0x1a03
Dpc flags = 0x0
MBX flags = 0x0
Link down Timeout = 008
Port down retry = 016
Login retry count = 016
Commands retried with dropped frame(s) = 0
Product ID = 4953 5020 2020 0002


SCSI Device Information:
scsi-qla0-adapter-node=200000e08b835870;
scsi-qla0-adapter-port=210000e08b835870;
scsi-qla0-target-0=50001fe150063029;
scsi-qla0-target-1=50001fe15006302b;
scsi-qla0-target-2=50001fe15006302d;
scsi-qla0-target-3=50001fe15006302f;

SCSI LUN Information:
(Id:Lun) * - indicates lun is not registered with the OS.
( 0: 0): Total reqs 21, Pending reqs 0, flags 0x0, 0:0:81 00
( 0: 1): Total reqs 76, Pending reqs 0, flags 0x0, 0:0:81 00
( 1: 0): Total reqs 21, Pending reqs 0, flags 0x0, 0:0:82 00
( 1: 1): Total reqs 61, Pending reqs 0, flags 0x0, 0:0:82 00
( 2: 0): Total reqs 21, Pending reqs 0, flags 0x0, 0:0:83 00
( 2: 1): Total reqs 61, Pending reqs 0, flags 0x0, 0:0:83 00
( 3: 0): Total reqs 21, Pending reqs 0, flags 0x0, 0:0:84 00
( 3: 1): Total reqs 61, Pending reqs 0, flags 0x0, 0:0:84 00
::::::::::::::
/proc/scsi/qla2xxx/2
::::::::::::::
QLogic PCI to Fibre Channel Host Adapter for QLA2340:
Firmware version 3.03.02 IPX, Driver version 8.00.00b21-k
Entry address = f8861000
ISP: ISP2312, Serial# C48138
Request Queue = 0x37740000, Response Queue = 0x37780000
Request Queue count = 2048, Response Queue count = 512
Total number of active commands = 0
Total number of interrupts = 10156
Device queue depth = 0x20
Number of free request entries = 1680
Number of mailbox timeouts = 0
Number of ISP aborts = 0
Number of loop resyncs = 0
Number of retries for empty slots = 0
Number of reqs in pending_q= 0, retry_q= 0, done_q= 0, scsi_retry_q= 0
Host adapter:loop state = , flags = 0x1a03
Dpc flags = 0x0
MBX flags = 0x0
Link down Timeout = 008
Port down retry = 016
Login retry count = 016
Commands retried with dropped frame(s) = 0
Product ID = 4953 5020 2020 0002


SCSI Device Information:
scsi-qla1-adapter-node=200000e08b834ac9;
scsi-qla1-adapter-port=210000e08b834ac9;
scsi-qla1-target-0=50001fe150063028;
scsi-qla1-target-1=50001fe15006302a;
scsi-qla1-target-2=50001fe15006302e;
scsi-qla1-target-3=50001fe15006302c;

SCSI LUN Information:
(Id:Lun) * - indicates lun is not registered with the OS.
( 0: 0): Total reqs 21, Pending reqs 0, flags 0x0, 1:0:81 00
( 0: 1): Total reqs 61, Pending reqs 0, flags 0x0, 1:0:81 00
( 1: 0): Total reqs 21, Pending reqs 0, flags 0x0, 1:0:82 00
( 1: 1): Total reqs 61, Pending reqs 0, flags 0x0, 1:0:82 00
( 2: 0): Total reqs 21, Pending reqs 0, flags 0x0, 1:0:83 00
( 2: 1): Total reqs 61, Pending reqs 0, flags 0x0, 1:0:83 00
( 3: 0): Total reqs 21, Pending reqs 0, flags 0x0, 1:0:84 00
( 3: 1): Total reqs 64, Pending reqs 0, flags 0x0, 1:0:84 00
proc_qla.txt lines 40-92/92 (END)

#proc_scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 06 Lun: 00
Vendor: PE/PV Model: 1x6 SCSI BP Rev: 1.1
Type: Processor ANSI SCSI revision: 02
Host: scsi0 Channel: 02 Id: 00 Lun: 00
Vendor: MegaRAID Model: LD0 RAID1 69358R Rev: 2.37
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 00 Lun: 00
Vendor: HP Model: HSV210 Rev: 5031
Type: RAID ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 00 Lun: 01
Vendor: HP Model: HSV210 Rev: 5031
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 01 Lun: 00
Vendor: HP Model: HSV210 Rev: 5031
Type: RAID ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 01 Lun: 01
Vendor: HP Model: HSV210 Rev: 5031
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 02 Lun: 00
Vendor: HP Model: HSV210 Rev: 5031
Type: RAID ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 02 Lun: 01
Vendor: HP Model: HSV210 Rev: 5031
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 03 Lun: 00
Vendor: HP Model: HSV210 Rev: 5031
Type: RAID ANSI SCSI revision: 05
Host: scsi1 Channel: 00 Id: 03 Lun: 01
Vendor: HP Model: HSV210 Rev: 5031
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi2 Channel: 00 Id: 00 Lun: 00
Vendor: HP Model: HSV210 Rev: 5031
Type: RAID ANSI SCSI revision: 05
Host: scsi2 Channel: 00 Id: 00 Lun: 01
Vendor: HP Model: HSV210 Rev: 5031
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi2 Channel: 00 Id: 01 Lun: 00
Vendor: HP Model: HSV210 Rev: 5031
Type: RAID ANSI SCSI revision: 05
Host: scsi2 Channel: 00 Id: 01 Lun: 01
Vendor: HP Model: HSV210 Rev: 5031
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi2 Channel: 00 Id: 02 Lun: 00
Vendor: HP Model: HSV210 Rev: 5031
Type: RAID ANSI SCSI revision: 05
Host: scsi2 Channel: 00 Id: 02 Lun: 01
Vendor: HP Model: HSV210 Rev: 5031
Type: Direct-Access ANSI SCSI revision: 05
Host: scsi2 Channel: 00 Id: 03 Lun: 00
Vendor: HP Model: HSV210 Rev: 5031
Type: RAID ANSI SCSI revision: 05
Host: scsi2 Channel: 00 Id: 03 Lun: 01
Vendor: HP Model: HSV210 Rev: 5031
Type: Direct-Access ANSI SCSI revision: 05

#system_info
System Information
------------------------

Date: Mon Apr 17 17:10:17 ALMST 2006

Red Hat Enterprise Linux AS release 4 (Nahant)
Kernel \r on an \m

Hostname: keglin.corp.kegoc.kz
Kernel: 2.6.9-5.ELsmp
Kernel is SMP
Architecture: i686
LVM version: package lvm is not installed

PCI Bus Info:

00:00.0 Host bridge: Intel Corp. E7501 Memory Controller Hub (rev 01)
00:02.0 PCI bridge: Intel Corp. E7500/E7501 Hub Interface B PCI-to-PCI Bridge (rev 01)
00:03.0 PCI bridge: Intel Corp. E7500/E7501 Hub Interface C PCI-to-PCI Bridge (rev 01)
00:04.0 PCI bridge: Intel Corp. E7500/E7501 Hub Interface D PCI-to-PCI Bridge (rev 01)
00:1d.0 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #1) (rev 02)
00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 42)
00:1f.0 ISA bridge: Intel Corp. 82801CA LPC Interface Controller (rev 02)
00:1f.1 IDE interface: Intel Corp. 82801CA Ultra ATA Storage Controller (rev 02)
01:1c.0 PIC: Intel Corp. 82870P2 P64H2 I/OxAPIC (rev 04)
01:1d.0 PCI bridge: Intel Corp. 82870P2 P64H2 Hub PCI Bridge (rev 04)
01:1e.0 PIC: Intel Corp. 82870P2 P64H2 I/OxAPIC (rev 04)
01:1f.0 PCI bridge: Intel Corp. 82870P2 P64H2 Hub PCI Bridge (rev 04)
02:02.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 0d)
03:01.0 Ethernet controller: Intel Corp. 82544GC Gigabit Ethernet Controller (LOM) (rev 02)
04:1c.0 PIC: Intel Corp. 82870P2 P64H2 I/OxAPIC (rev 04)
04:1d.0 PCI bridge: Intel Corp. 82870P2 P64H2 Hub PCI Bridge (rev 04)
04:1e.0 PIC: Intel Corp. 82870P2 P64H2 I/OxAPIC (rev 04)
04:1f.0 PCI bridge: Intel Corp. 82870P2 P64H2 Hub PCI Bridge (rev 04)
05:04.0 Fibre Channel: QLogic Corp. QLA2312 Fibre Channel Adapter (rev 02)
06:03.0 Fibre Channel: QLogic Corp. QLA2312 Fibre Channel Adapter (rev 02)
07:1c.0 PIC: Intel Corp. 82870P2 P64H2 I/OxAPIC (rev 04)
07:1d.0 PCI bridge: Intel Corp. 82870P2 P64H2 Hub PCI Bridge (rev 04)
07:1e.0 PIC: Intel Corp. 82870P2 P64H2 I/OxAPIC (rev 04)
07:1f.0 PCI bridge: Intel Corp. 82870P2 P64H2 Hub PCI Bridge (rev 04)
08:08.0 RAID bus controller: Dell PowerEdge Expandable RAID controller 4/Di (rev 01)
0b:04.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)

Module Info

Module Size Used by
md5 8001 1
ipv6 238817 16
autofs4 22085 0
i2c_dev 14273 0
i2c_core 25921 1 i2c_dev
sunrpc 137637 1
dm_mod 57157 0
button 10449 0
battery 12869 0
ac 8773 0
uhci_hcd 32729 0
e100 36037 0
mii 8641 1 e100
e1000 82637 0
floppy 58065 0
sg 38113 0
ext3 118473 11
jbd 59481 1 ext3
qla6312 116033 0
qla2300 126529 0
qla2xxx 109665 3 qla6312,qla2300
scsi_transport_fc 11713 1 qla2xxx
megaraid_mbox 33233 11
megaraid_mm 15205 1 megaraid_mbox
sd_mod 20545 13
scsi_mod 116557 5 sg,qla2xxx,scsi_transport_fc,megaraid_mbox,sd_mod

Disk Info:

sda 0,2,0,0 MegaRAID LD0 RAID1 69358R 2.37
sdb 1,0,0,1 HP HSV210 5031 5000-1fe1-5006-3029
sdc 1,0,1,1 HP HSV210 5031 5000-1fe1-5006-302b
sdd 1,0,2,1 HP HSV210 5031 5000-1fe1-5006-302d
sde 1,0,3,1 HP HSV210 5031 5000-1fe1-5006-302f
sdf 2,0,0,1 HP HSV210 5031 5000-1fe1-5006-3028
sdg 2,0,1,1 HP HSV210 5031 5000-1fe1-5006-302a
sdh 2,0,2,1 HP HSV210 5031 5000-1fe1-5006-302e
sdi 2,0,3,1 HP HSV210 5031 5000-1fe1-5006-302c

Filesystem Info:

Filesystem Type 1K-blocks Used Available Use% Mounted on
/dev/sda7 ext3 3020140 208628 2658096 8% /
/dev/sda1 ext3 101086 12399 83468 13% /boot
none tmpfs 1037468 0 1037468 0% /dev/shm
/dev/sda10 ext3 703596 17196 650660 3% /home
/dev/sda9 ext3 1004024 222364 730656 24% /tmp
/dev/sda5 ext3 5036284 3237300 1543152 68% /u01
/dev/sda3 ext3 15116868 70312 14278652 1% /u02
/dev/sda2 ext3 16126420 72792 15234316 1% /u03
/dev/sda12 ext3 22232228 1283012 19819852 7% /u04
/dev/sda6 ext3 4032092 1904632 1922636 50% /usr
/dev/sda11 ext3 497829 55860 416267 12% /var
/dev/sdb ext3 103212320 94272 97875168 1% /eva

qla2x00 RPM installed: package qla2x00 is not installed
hp_qla2x00 RPM installed: package hp_qla2x00 is not installed
hp_qla2x00src RPM installed: hp_qla2x00src-8.00.02p11-24
fibreutils RPM installed: fibreutils-1.11-3

OS sees one VDISK disk on 8 paths. At enabled multipath (ql2xfailover Default: 1) OS should see only one, similarly to /dev/sdb. Most likely ql2xfailover don't work.

How to solve this problem??!!

[Robert S. Cowan]

> Red Hat Enterprise Linux AS release 4 (Nahant)
> Kernel: 2.6.9-5.ELsmp

Upgrade your kernel so that you're at least at RHEL 4 U1. It appears there were pieces of the Qlogic driver in the pre-U1 kernel that override anything that's loaded (-k is the 'embedded' driver).

r

[Yermek Bissenbayev]

Dear Robert,

By your advice I'm update last kernel OS RHAS4
2.6.9-34.EL smp

Default version qlogic driver in new kernel:
QLogic PCI to Fibre Channel Host Adapter for QLA2340:
Firmware version 3.03.18 IPX, Driver version 8.01.02-d4

After I'm download from hp support site new relase driver hp_qla2x00src-8.01.03-14.linux.rpm

Please log update bellow:
#rpm -ivh hp_qla2x00src-8.01.03-14.linux.rpm
hp_qla2x00src ##################################################
Loaded driver is in nonfailover mode
Writing new /etc/hp_qla2x00.conf...done
Copying /opt/hp/src/hp_qla2x00src/libqlsdm-ia32.so to /usr/lib/libqlsdm.so
Modifying /etc/hba.conf
Kernel modules directory: /lib/modules/2.6.9-34.EL.rootsmp/kernel/drivers/scsi/qla2xxx
Kernel build directory: /lib/modules/2.6.9-34.EL.rootsmp/build

Enabling failover in /lib/modules/2.6.9-34.EL.rootsmp/build/.config

make clean
make: Entering directory `/usr/src/kernels/2.6.9-34.EL.root-smp-i686'
make: Leaving directory `/usr/src/kernels/2.6.9-34.EL.root-smp-i686'

make -j5 -C /lib/modules/2.6.9-34.EL.rootsmp/build M=/opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03 modules
make: Entering directory `/usr/src/kernels/2.6.9-34.EL.root-smp-i686'
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/ql2100.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/ql2100_fw.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/ql2200.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/ql2200_fw.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/ql2300.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/ql2300_fw.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/ql2322.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/ql2322_fw.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/ql2400.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/ql2400_fw.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla_os.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla_init.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla_mbx.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla_iocb.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla_isr.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla_gs.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla_dbg.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla_sup.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla_rscn.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla_xioct.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla_inioct.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla_fo.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla_foln.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla_cfg.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla_cfgln.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla_32ioctl.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla_ip.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/ql6312.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/ql6312_fw.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2xxx_conf.o
CC [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2xip.o
HOSTCC /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/extras/qla_nvr
HOSTCC /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/extras/qla_opts
LD [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2xxx.o
LD [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2100.o
LD [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2200.o
LD [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2300.o
LD [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2322.o
LD [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla6312.o
LD [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2400.o
Building modules, stage 2.
MODPOST
CC /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2100.mod.o
CC /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2200.mod.o
CC /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2300.mod.o
CC /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2322.mod.o
CC /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2400.mod.o
CC /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2xip.mod.o
CC /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2xxx.mod.o
CC /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2xxx_conf.mod.o
CC /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla6312.mod.o
LD [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2100.ko
LD [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2200.ko
LD [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2300.ko
LD [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2322.ko
LD [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2400.ko
LD [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2xip.ko
LD [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2xxx.ko
LD [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla2xxx_conf.ko
LD [M] /opt/hp/src/hp_qla2x00src/qla2xxx-8.01.03/qla6312.ko
make: Leaving directory `/usr/src/kernels/2.6.9-34.EL.root-smp-i686'

Saving old qla2xxx.ko
Copying qla2xxx.ko to /lib/modules/2.6.9-34.EL.rootsmp/kernel/drivers/scsi/qla2xxx
Saving old qla2300.ko
Copying qla2300.ko to /lib/modules/2.6.9-34.EL.rootsmp/kernel/drivers/scsi/qla2xxx
Saving old qla2400.ko
Copying qla2400.ko to /lib/modules/2.6.9-34.EL.rootsmp/kernel/drivers/scsi/qla2xxx
Saving old qla6312.ko
Copying qla6312.ko to /lib/modules/2.6.9-34.EL.rootsmp/kernel/drivers/scsi/qla2xxx
Copying qla2xxx_conf.ko to /lib/modules/2.6.9-34.EL.rootsmp/kernel/drivers/scsi/qla2xxx
Running depmod -a

adding line to /etc/modprobe.conf: alias scsi_hostadapter1 qla2xxx_conf
adding line to /etc/modprobe.conf: alias scsi_hostadapter2 qla2xxx
adding line to /etc/modprobe.conf: alias scsi_hostadapter3 qla2300
adding line to /etc/modprobe.conf: alias scsi_hostadapter4 qla2400
adding line to /etc/modprobe.conf: alias scsi_hostadapter5 qla6312
adding line to /etc/modprobe.conf: options qla2xxx ql2xmaxqdepth=16 qlport_down_retry=64 ql2xloginretrycount=30 ql2xfailover=0 ql2xlbType=0 ql2xautorestore=0x0
Adding "remove qla2xxx" line to /etc/modprobe.conf

Creating new initrd - initrd-2.6.9-34.EL.rootsmp.img

Making symbolic link from /opt/hp/src/hp_qla2x00src/master.sh to /usr/sbin/hp_compile_qldriver
qla2x00 driver source can be found in /opt/hp/src/hp_qla2x00src

After reboot server error message:
qla2xxx_conf: version magic '2.6.9-34.EL.rootsmp SMP 686 REGPARM 4KSTACKS gcc-3.2' should be '2.6.9-34.EL.rootsmp SMP 686 REGPARM 4KSTACKS gcc-3.4'
qla2xxx: version magic '2.6.9-34.EL.rootsmp SMP 686 REGPARM 4KSTACKS gcc-3.2' should be '2.6.9-34.EL.rootsmp SMP 686 REGPARM 4KSTACKS gcc-3.4'
qla2300: version magic '2.6.9-34.EL.rootsmp SMP 686 REGPARM 4KSTACKS gcc-3.2' should be '2.6.9-34.EL.rootsmp SMP 686 REGPARM 4KSTACKS gcc-3.4'
qla2400: version magic '2.6.9-34.EL.rootsmp SMP 686 REGPARM 4KSTACKS gcc-3.2' should be '2.6.9-34.EL.rootsmp SMP 686 REGPARM 4KSTACKS gcc-3.4'
qla6312: version magic '2.6.9-34.EL.rootsmp SMP 686 REGPARM 4KSTACKS gcc-3.2' should be '2.6.9-34.EL.rootsmp SMP 686 REGPARM 4KSTACKS gcc-3.4'

Please, Your opinion!

[Yermek Bissenbayev]

Problem solved after reinstall OS and build the driver sources from Qlogic site qla2xxx-v8.01.03-dist.tgz
Version 8.01.03
FW version QLA22xx: 2.02.08 TP