- Community Home
- >
- Software
- >
- HPE OneView
- >
- Re: stuck applying server profile
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-26-2017 07:49 AM
07-26-2017 07:49 AM
stuck applying server profile
on our freshly installed OneView 3.10, our deployment will get stuck deploying server profiles.. it goes thru, applies bios settings and shuts off the server and stays at 'applying boot mode settings' for hours until it finally gives up.
It looks to have applied the bios settings, also applies the SPP firmware to the DL 380 Gen9, but thats it..
When it gives it, it has this error.. Odd because it does boot off the SPP as it applies the FW ok, and wouldnt be a block issue as it works prior..
Any help would be greatly appreciated. thanks
Ensure that the SPP selected is valid and bootable. Also check if the iLO has network connectivity and the virtual media port has not been blocked by a firewall. Cold boot the server, enter the ROM-Based Setup Utility by selecting F9 at the appropriate time during POST, and ensure that the USB Controls are enabled and restore to default system settings. Once the server is booted, power it off and retry the operation. Alternatively reset the iLO. If the problem persists, contact your authorized support representative and provide them with a support dump.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-27-2017 06:21 AM
07-27-2017 06:21 AM
Re: stuck applying server profile
Try to reset BIOS settings to default before applyng OV profile
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-07-2019 11:10 AM
11-07-2019 11:10 AM
Re: stuck applying server profile
I just had this issue with the latest 5.00.00.02 OneView appliance and found that the reason is because my iLO License is standard..
Upgrade to iLO Advanced and that should fix it up.. You can see what type of license you have by looking on the main info page in iLO. $$$$
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-08-2019 02:46 AM
11-08-2019 02:46 AM
Re: stuck applying server profile
I'm also stuck with this issue running OneView 5.00.00.02 on all our BL460c Gen8 blades. It still seems to be OK with older G7 systems. HPE OneView license without iLO Advanced is used for all blades.
I can't find any hint in the release notes or compability matrix that iLO Advanced would be needed and this would definitly be a breaking update.
@Treybizzle : What kind of server hardware was affected in your environment? Did you get any official feedback on this from HPE?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-11-2019 04:37 AM
11-11-2019 04:37 AM
Re: stuck applying server profile
Got the following from HPE support:
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-28-2019 05:57 AM
11-28-2019 05:57 AM
Re: stuck applying server profile
HPE just released an update to 5.00.01-0410269. I can confirm that this fixes the issue with applying server profiles (with BIOS or FW settings) and the standard blade license.
It seems that this version introduced new "challenges", at least in our test environment.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-19-2020 08:09 AM
02-19-2020 08:09 AM
Re: stuck applying server profile
I am using a BL460c Server and have OneView Upgraded to v5.00.00.02 and still unable to apply the server profile.. what did you do to fix this?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-19-2020 08:16 AM
02-19-2020 08:16 AM
Re: stuck applying server profile
Ahh I see the new update from 5.00.00.02-0404934 to 5.00.01... phew I will update and then try again.
Thanks for the tip!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-19-2020 10:41 PM
02-19-2020 10:41 PM
Re: stuck applying server profile
@Treybizzle Would like to hear from you if face any new issues after the update. I'm having issues with some basic configuration settings for the c7000 enclosures (setting NTP source). Working since weeks on that with HPE support.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-20-2020 05:31 AM
02-20-2020 05:31 AM
Re: stuck applying server profile
Hmmm I see, I don't believe we use NTP conifiguration in our OneView.. can you give more details as to what the problem is?
Time and Locale
- Current date/time 2/20/20 8:31:34 am (UTC -0500)
- Network time server not configured
- Locale English (United States)
- Current date/time
I was able to apply the server profile now that I'm running the updated version of OneView. woohoo!