rx 2620 shutdown by itself

[Sakui]

Hi Guys,

I am still getting the following error continually. I have change the motherboard.


Mar 28 23:40:15 /usr/sbin/envd[1368]: terminated by signal 15
Mar 28 23:40:15 rpcbind: terminate: rpcbind terminating on signal. Restart with
"rpcbind -w"
Mar 28 23:40:15 /usr/sbin/envd[1368]: terminated by signal 15
Mar 28 23:40:15 rpcbind: terminate: rpcbind terminating on signal. Restart with
"rpcbind -w"

[Phil uk]

Hi,

Did you replace the System board because of the errors that you posted above, or are you getting the errors as a result of changing the system bd????

Did you put the top cover back on properly?

Can you post the MP Error logs please?

Regards,
Phil

[Sakui]

I change the system board because i was getting this

/usr/sbin/envd[1368]: terminated by signal 15. All my diagnostic lights are off including my LAN LED.

I can boot the server to unix but after a few while it shutdown by itself.


SYSREV

Current firmware revisions

MP FW : E.03.32
BMC FW : 04.01
EFI FW : 05.46
System FW : 04.10
This was the last message on the screen.

Shutting down machine, please wait.

Shutdown complete.

sync'ing disks (0 buffers to flush):
0 buffers not flushed
0 buffers still dirty

Closing open logical volumes...
Done


634 BMC 2 0x2047ED7C0F022C90 FA00A370FA120300 Type-02 127003 1208323
28 Mar 2008 23:15:27
633 BMC 2 0x2047ED7C0F022C80 FFFF056FFA220300 Type-02 226f05 2256645
28 Mar 2008 23:15:27
632 BMC 2 0x2047ED7C0E022C70 020EA37002120300 Type-02 127003 1208323
28 Mar 2008 23:15:26
631 BMC *7 0x2047ED7C0E022C60 020EA87002120300 Type-02 127008 1208328
28 Mar 2008 23:15:26
630 BMC 2 0x2047ED7C0C022C50 020EA37002120300 Type-02 127003 1208323
28 Mar 2008 23:15:24
629 BMC *7 0x2047ED7C0C022C40 020EA87002120300 Type-02 127008 1208328
28 Mar 2008 23:15:24
628 BMC 2 0x2047ED7C0B022C30 020EA37002120300 Type-02 127003 1208323
28 Mar 2008 23:15:23
627 BMC *7 0x2047ED7C0B022C20 020EA87002120300 Type-02 127008 1208328
28 Mar 2008 23:15:23
626 BMC 2 0x2047ED7C0A022C10 020EA37002120300 Type-02 127003 1208323
28 Mar 2008 23:15:22

[Phil uk · Accepted solution]

Hi,

Your machine is giving chassis open errors.
It is therefore shutting down as it thinks the cover is off.

You will need to visually inspect the servers as per my below.
Check the switch as per my answer at the bottom of this thread.
http://forums12.itrc.hp.com/service/forums/questionanswer.do?threadId=1198960

Regards,
Phil

[Sandy Chen]

Hi,

Can you tried to upgrade your system firmware? Latest one is 04.29

Regards,
Sandy

[YAQUB_1]

Hi Sakui,

As per Ur system MP event log analysis report is here:-

Keyword = SHUTDOWN_OR_RESET_ON_SENSOR

A sensor reading in the system was determined to be non-recoverable and the system was shut down or reset. Read the system logs to find which sensor was out of range.

Can U send us system syslog and then we can find out what is the actual problem Ur system.

Thanks--Yaqub
I am a Customer Advocate!!!

[Sakui]

Thanks so much to Philp UK. It was a chasis sensors issue.