- Community Home
- >
- Networking
- >
- Wireless
- >
- M and MSM Series
- >
- MSM430
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-14-2014 07:56 AM
04-14-2014 07:56 AM
Re: MSM460
This:
setup_arch: bootmem
mpc85xx_rdb_setup_arch()
arch: exit
... is NOT, repeat NOT an error message. It does not imply that the AP is failing. It just means that the console settings are incorrect. That does not really matter, as the console port isn't intended for a management interface in the first place. It's a troubleshooting tool in case you run into problems, only really useful for us geeks here.
For Juggyv's issue I double Peter - call support to get startup file. When you do it correctly it's only a few second job, and it usually does get a device back to its senses.
Sanjay, I'm sorry but I do not really follow you. Do you have a controlled environment? If yes, then you do not configure the AP at all. The only config to do is to provision the AP if you use L3 discovery.
My suggestion:
1. Connect the suspect AP to the same switch and VLAN where your controller connects to - the interface you use for discovering, that is.
2. Restore factory default settings as described by Rudy. I'd like to clarify the procedure a bit, though.
- Press Reset
- All LEDs will come ON for a couple of seconds
- All LEDs will go OFF for a couple of seconds
- All LEDs will start blinking slowly (~1/sec)
- On the third slow blink release Reset button.
The controller should pick up the AP.
To put the device in the TFTP mode you follow exactly the same process, except for last step. You keep the Reset button pressed until all LEDs start blinking faster (~2/sec). Then release Reset, and the AP will default to 192.168.1.1 and accept FW flash through TFTP. However as Peter said normal FW file won't work, but you will need to contact support.
HTH,
Arimo
HPE Networking Engineer
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-25-2014 06:38 AM
05-25-2014 06:38 AM
Re: MSM460
Hi - this ended up being a dud - No firmware up/down etc or pinning it would work. HP swapped it and everything back to normal. A big waste of time. If you get an AP that displays similar traits and is not contactable in any way then I suggest getting HP To swap it.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-09-2016 04:12 AM
08-09-2016 04:12 AM
Re: MSM460
reset doesn't work, i still see
setup_arch: bootmem
mpc85xx_rdb_setup_arch()
arch: exit
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-29-2016 10:59 AM
09-29-2016 10:59 AM
Re: MSM460
Hope someone can upload special firmware that they've mentioned above to here so that we can download.
Now I have some AP met this problem. The only way for me is contact HP support and replace new one.
But I still need way how to fix by myself
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-09-2017 10:08 AM
09-09-2017 10:08 AM
Re: MSM460
This worked a treat.
I don't thinks its 3 blinks though. I hit the reset button, blinks once after a few seconds. Thereafter I waited another 3 blinks and on the third I let go.
Thanks!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-07-2021 09:14 PM
07-07-2021 09:14 PM
Re: MSM460
I can access COM1 CLI with parameters - speed 115200 bps & no flow controll.
- « Previous
-
- 1
- 2
- Next »