Need the xxx.cim.startup for HP 560

[podge3]

Anyone know where/how I can get the xxx.cim.startup for the HP 560?

Thanks.

[RamKrish]

I have sent you a private message with a link to download the startup file.

Ram

[podge3]

Thanks!

[Kristian Gyllström]

Me too have this problem on three new HP 560 Access Points that we need to convert to stand-alone. Please send us the link. Thank you!

[ProfessorH]

Please send me this link as well. We just got a new 560 and it has the boot image that has only provisioning mode and I need to get 6.6.0 on there.

[RamKrish]

Hi

Are you trying to use the HP560 into controlled mode or autonomous mode?

If the intention is to use in controlled mode, then all you need to do is to simply plug the AP into the controlller environment.  It should be able to get the code from the controller. 

Once it gets the code from the controller, you may choose to convert the AP into autonomos mode.

Regards

Ram

[hny1]

Dear concerned ,

i also want to use an AP in MSM autonomous mode and i do not have an MSM Controller. 

i need to download xxx.cim.startup file. 

please help

regard

Haroon Naseem

[RamKrish]

I just figured it out we have the .startup.cim file available on the software download page (need to use your HP passport login to get to the download section)

Download page for HP560:  Under HP My Networking --> My Software --> look for 560 search, that should take you to the download page).

URL for Download page:

https://h10145.www1.hpe.com/downloads/DownloadSoftware.aspx?SoftwareReleaseUId=11635&ProductNumber=J9846A&lang=&cc=&prodSeriesId=&OrderNumber=&PurchaseDate=

Upgrade Procedure:

Refer to section (Load Method 2: Using TFTP)

http://h20565.www2.hpe.com/hpsc/doc/public/display?sp4ts.oid=6898336&docId=emr_na-c04514138&docLocale=en_US

Hope this helps.

[Tomasz_J]

I also need this file  - could somene post link here?

Rgds

[y7y_k7]

Hello,

could you please send me the link i have the same problem.

B.R

[sector7g]

also need the xxx.cim.startup  for msm560

sry to dig up an old thread but this thing is harder to find than a virgin in a strip club!

[RamKrish]

If you have read the full thread, there is an URL for the image download page.  Once downloaded, the ZIP archive contains the software (both .cim and .startup.cim files), the release notes and the SNMP MIB files.

URL for the download page:  https://h10145.www1.hpe.com/downloads/DownloadSoftware.aspx?SoftwareReleaseUId=11635&ProductNumber=J9846A&lang=&cc=&prodSeriesId=&OrderNumber=&PurchaseDate=

URL for the TFTP procedure document:  http://h20565.www2.hpe.com/hpsc/doc/public/display?sp4ts.oid=6898336&docId=emr_na-c04514138&docLocale=en_US

[sector7g]

thanks not true, I downloaded

V6.6.2.0-HP560-MSM410-MSM430-MSM460-MSM466-MSM466R-B22792.zip

which contains

mibs-B22792.tar.gz

5998-8265_MSM_3457_RN_6620_Oct-23_web.pdf

V6.6.2.0-HP560-MSM410-MSM430-MSM460-MSM466-MSM466R-B22792.cim

no startup file .cim

thanks though.

[sector7g]

Apologies, the link didnt work initially but I tried it again & logged back in & got it.

V6.5.0.1-HP560-B19720.zip

The zip contains

V6.5.0.1-HP560-B19720.cim.startup 

Perfect thank you.

[ICCNETMGR]

I have ran into a similar problem with a MSM466 and it took me quite a while to navigate and find the correct information to correect the problem.

A couple of things, the firmware mentioned throughout several of these posts will work on the following APs: HP 425, 517, 560 as well as the MSM 430, 460, 466 and 466-R, which is per the v6.5.0.1 zip file release notes.

Next, if anyone receives a TFTP error, such as "Error on server: / Boot <code> (<date>) / Image validation failed: bad magic", this error is due to not using the "xxx.cim.startup" file or possibly it is corrupt.

One last hurdle was the AP started in controller mode ready to be provisioned for a controller.  Even though one should be able to switch it to autonomous mode within the AP menu, it would not.  Allowed it to connect to a MSM controller which updated(sync'd) the firmware and then selected the AP within the Defult Group.  Next, select menu Maintenance / System and "Switch to Autonomous Mode" which finally worked.

[YuriPaiva]

Hi everyone,

I had issue in a MSM460. I though It was in failure state since I cound ping in the address 192.168.1..1 but could not log in the web console and was not detected buy a MSM760 Controller in my bussiness place.

Searching in this forum I found a post about the Access Point could be in controlled mode by Unified HP Solution and needs to be software converted by MSM HP Wlan Solution and in thus mode operate managed by a MSM Controller or in Autonomus mode.

I converted the MSM 460 with the software V6.5.0.1-HP560-B19720.cim.starup and works fine for me, in the controlled mode and in the autonomus one.

To load the software you have to put the MSM460 in tftp mode. For that put a paper clip in the reset botton, press it until the leds blink twice por second and release the paper clip.

Pay attention is about the tftp file transfer it should be done in the binary mode in the tftp client. In Windows Enviroment the comand line is tftp -i 192.168.1.1 V6.5.0.1-HP560-B19720.cim.starup image

It takes about 30 seconds to load the file and receive the message por sucessfull file transfer, the MSM460 will install the software and reboot. After that you need to reset the access to factory defaults to log in the web console. The factory defaults the AP is in controlled mode. 

[Terrific]

Could you please share startup.cim files for msm430 also?

[LALOKORN]

Hellow,

Can you help me with the startup file to restore my AP please?

[redcon_floripa]

I'm also looking for a .cim.startup file compatible with our MSM430.  Its a brazilian version JL009-60011, brand new in the box and phone support told me they can't help...
I've tried the 560 version but it didn't work well, in fact it put one AP in a weird state, where it would reboot every 30 minutes and the web interface is all strange, not really working...

[techin]

@redcon_floripa, I really think you should consider creating a completely new post instead. Creating a new post helps..dont know why

[grinya]

I tried cim.sturtup for MSM560, my MSM430 accepted it and fix this problem

.cim.sturtup  подходит от 560.

Решил проблему с загрузкой 430 точки.

инструкция по прошивке тут (метод 2) https://support.hpe.com/hpesc/public/docDisplay?docLocale=en_US&docId=emr_na-c04514138

Скачал и  sturtup (для 560) и прошивку 6.6.9.1 (для 430) с сайта hpe..