- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- command for HBA
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-18-2010 11:23 AM - last edited on 04-08-2014 06:50 PM by Lisa198503
05-18-2010 11:23 AM - last edited on 04-08-2014 06:50 PM by Lisa198503
good afternoon,
now I have an HBA card with this status:
Driver state = AWAITING_LINK_UP
That command I can use to reset the card?
fcmsutil-f enable? this work?
operation system: HP-UX 11.23
P.S. This thread has been moved from Disk to HP-UX > sysadmin. -HP Forum Moderator
Solved! Go to Solution.
- Tags:
- HBA
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-18-2010 11:30 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-18-2010 11:32 AM
05-18-2010 11:32 AM
Re: command for HBA
If you want to reset the card you should use:
fcmsutil /dev/CARD reset
where CARD is your fibre channel card.
It can be found with the following command:
ioscan -fnkCfc
Just make sure that your port at the switch is enabled and I also kindly advice you to set explicitly the port speed (2/4/8Gbps) at the side of the switch!
Regards,
Sve
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-18-2010 11:38 AM
05-18-2010 11:38 AM
Re: command for HBA
I need to restart the HBA card to verify whether active or not.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-18-2010 11:55 AM
05-18-2010 11:55 AM
Re: command for HBA
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-18-2010 12:15 PM
05-18-2010 12:15 PM
Re: command for HBA
If lights are lit and fcmsutil is still in the state listed above:
1) Possible problem on the fiber network
2) Fiber switch may need to be configured to an online status.
The HP-UX serve should pick up this status instantly without need to reboot.
SEP
Owner of ISN Corporation
http://isnamerica.com
http://hpuxconsulting.com
Sponsor: http://hpux.ws
Twitter: http://twitter.com/hpuxlinux
Founder http://newdatacloud.com
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-18-2010 12:19 PM
05-18-2010 12:19 PM
Re: command for HBA
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-18-2010 12:35 PM
05-18-2010 12:35 PM
Re: command for HBA
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-18-2010 12:41 PM
05-18-2010 12:41 PM
Re: command for HBA
No, to reset the HBA card when it is not ONLINE does not require a down system.
I would not reset the HBA card while ONLINE and having file systems mounted on disks it provides.
In the current situation, no downtime appears to be required.
SEP
Owner of ISN Corporation
http://isnamerica.com
http://hpuxconsulting.com
Sponsor: http://hpux.ws
Twitter: http://twitter.com/hpuxlinux
Founder http://newdatacloud.com
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-18-2010 05:11 PM
05-18-2010 05:11 PM
Re: command for HBA
then do a fcmsutil command to reset the HBA
/opt/fcms/bin/fcmsutil
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-22-2010 03:32 PM
05-22-2010 03:32 PM