HP9000 L2000 , modem conf

Hi,
I have configured an external modem in an HP9000 L2000 box, everything seems to be ok, I dial in in to the box and receive the HP-UX login, but whatever I write is not get it by the box, I have configured in the box, VT100, SW flow control, 8 data bits, no parity, 1 stop bit. Does anyone have any idea? Thanks!!

11 REPLIES 11

Dear ,

If u are dialing--in please put the inittab entry of respawn to off.

i hope this will help you.

an

Om Shanti Om

Hi, I think the problem is because I cant send the BREAK key to the 9000 box,

After dial into the 9000 box I got:
# ps -ef | grep ttyd0p2
root 6174 1 0 18:57:19 ttyd0p2 0:00 /usr/sbin/getty -h ttyd0p2 H

and:
# stty < /dev/ttyd0p2
speed 9600 baud; -parity hupcl clocal
min = 1; intr = ^C;
eof = ^A; swtch ;
brkint -inpck -istrip icrnl onlcr tab3
-iexten echo -echoe echok
-echoctl -echoke

I send CTRL C several times but the result is the same. I cant sent the user and the password, I cant write anything.

# echo "123" > /dev/ttyd0p2
writes 123 in my hyperterminal session. the problem is from the remote session to the 9000 box.

Any idea?

Thanks in advance.

Regards.

What kind of software you used for Dial-up? Do you use Procomm plus? If yes then after getting connected select "Send Break or ALT B" from DATA pull down option, which will send a break signal and you will be connected to the system.

What kind of software you used for Dial-up? Do you use Procomm plus? If yes then after getting connected select "Send Break or ALT B" from DATA pull down option, which will send a break signal and you will be connected to the system.

What kind of software you used for Dial-up? Do you use Procomm plus? If yes then after getting connected select "Send Break or ALT B" from DATA pull down option, which will send a break signal and you will be connected to the system.

What kind of software you used for Dial-up? Do you use Procomm plus? If yes then after getting connected select "Send Break or ALT B" from DATA pull down option, which will send a break signal and you will be connected to the system.

What kind of software you used for Dial-up? Do you use Procomm plus? If yes then after getting connected select "Send Break or ALT B" from DATA pull down option, which will send a break signal and you will be connected to the system.

Sorry for the repeated messages, I thought the reply was not posted as it was giving me an error.

I am using MS HyperTeminal.

What does your gettydefs file entry look like for your modem ?? we use the following;

hpmod96 # B9600 HUPCL SANE CS8 ISTRIP IXANY TAB3
# B9600 HUPCL SANE CS8 ISTRIP IXANY TAB3
#Modem 9600 login: #hpmod96

And in /etc/inittab;

a0:234:respawn:/etc/getty -h -t 60 ttyd0p0 hpmod96

And I use MS HyperTerminal from my PC at home, it works fine. This should work for you too. You didnt say what type of modem you are using ?? If you still have problems its the entries in the gettydefs file you need to change.

Im from Palmerston North, New Zealand, but somehow ended up in London...

Hi:
I am using an external ACERModem 56 Surf.

The line is:
9600 # B9600 HUPCL IGNPAR PARENB ICRNL IXON OPOST ONLCR CS7 CREAD ISIG ICANON ECHO ECHOK PARENB ISTRIP IXANY TAB3
# B9600 SANE CS7 PARENB ISTRIP IXANY TAB3 HUPCL
#login: #300

# ps -ef | grep tty
root 8071 1 0 09:13:20 ? 0:00 /usr/lbin/uucp/uugetty -r -t 60 -h ttyd0p2 9600