Ignite

[donne007]

I have Installed Ignite server on a HP Ux 11.0 Box and when i ,m trying to configure and create a S/w depot using the CDROm it throws an error
" The Directory for file /var/opt/ignite/data/Rel_B.10.20/core_700.cfg specified -c does not exist"
" /opt/ignite/bin/make_config -c /var/opt/ignite/data/Rel_B.10.20/Core_700_cfg -s /cdrom -a 700 failed "

Is it Possible to pull Install a 10.2 HpUx,from a Ignite Box Running Hp Ux 11.0, if Yes , can any one help me on this. Bcoz the ignite Server is a BClass wks and the client is a 712 wks ..
can any one help me on this
Thanks in advance
Asif

[Martin Burnett_2]

Hello Asif,

It sounds like you installed the 11.0 ONLY version of Ignite. In this case there is no /var/opt/ignite/data/Rel_B.10.20 directory installed. Check the filesets of your Ignite product, if you do not see the following filesets you must install the ALL version of Ignite to be able to install 10.20 or 11.11 systems from an 11.00 server:


# swlist -l fileset |grep -i ignite
...truncated....
Ignite-UX.FILE-SRV-10-20 B.3.7.96 File Archives Used By Cli
ents During HP-UX Install
Ignite-UX.FILE-SRV-11-00 B.3.7.96 File Archives Used By Cli
ents During HP-UX Install
Ignite-UX.FILE-SRV-11-11 B.3.7.96 File Archives Used By Cli
ents During HP-UX Install
....truncated....

The hardware the ignite server software is installed on is irrelevant to the type of installation you can perform. So there should be no problem installing from B-class workstation to 712.


Thanks for participating in the forums,

Martin
Chaos reigns within. Reflect, repent, and reboot. Order shall return.

[donne007]

Thanx Martin,
I tried But no luck again it's giving me the same erroe the Filesset mentioned by you are ther and i even tried copying the CD to a Source Depot that too gives me the same error and # swreg -l depot @ "Mount Pont"
is of no use .. Any Updat on this ,,
Thanx in advance
Asif

[Denise Kent]

Yes you can do a pull install from the client, do
#boot lan. install

Might also help to read IUX admin guide:

http://www.software.hp.com/products/IUX/docs/sysadm.html

Kind regards
Denise

[donne007]

Thanks Dennnis.
The problem is while creating an SD Depot wher i use the "use a CDROM "option and it throws me an error
"/opt/ignite/bin/make_config-c /var/opt/ignite/data/rel_B.10.20/core_700_cfg -s /iuxcdrom0 -a failed "
iuxcdrom0 is mount point of cdrom.
i tried Installing Ignite-Ux for 10.01.10.20& 11 and is ther some thing to check in the core_700_cfg file "

Thanks
Asif

[Martin Burnett_2]

Hello Asif,

Well your original error says the file does not exist:

" The Directory for file
/var/opt/ignite/data/Rel_B.10.20/core_700.cfg specified -c does not exist"

Doe sit exist? What are the permissions on it? Check your syntax is correct?

You need to post the output from:

# swlist -l fileset |grep -i ignite

So I can see what version of Ignite and which filesets you have.

Please check this procedure to make sure that you have setup Ignite correctly:

http://www.software.hp.com/products/IUX/docs/sysadm.html

Thanks for participating in the forums,

Martin
Chaos reigns within. Reflect, repent, and reboot. Order shall return.

[Judy Traynor]

Martin is correct -
Use the Application CD to install the 10.20 version of ignite, and it will work. Those Dirs are set up when you install the ignite Software/VERSION on your system (I Think it is on App CD 1 of 4) but may be mistaken.

Good Luck,
(Do what Martin said and you will be OK)

Jim

[donne007]

Thanx Martin
The Problem was that the "var/opt/ignite/data/Rel_B.10.20/core_700.cfg specified " File Does'nt had a Execute Permission.
Finally I cud create SD Depot after Ganting the Execute Permsiion for Group.


Thankx For The Splendid Support and Guidance
Good Luck Asif