- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Lock disk creation documentation
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-14-2008 05:48 AM
тАО07-14-2008 05:48 AM
I can not find anywhere in the documentation the exact steps for creating the lock disk. I have created and populated all the other disks using pvcreate, lvm and vg commands. Hardware is identical to the existing system even down to the i/o paths. I have no problem reading the manual, I just haven't been able to find specifics.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-14-2008 06:02 AM
тАО07-14-2008 06:02 AM
Re: Lock disk creation documentation
check lock pv name in cluster ascii config file. and do cmapplyconf again.
Kenan.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-14-2008 06:16 AM
тАО07-14-2008 06:16 AM
Re: Lock disk creation documentation
Perhaps link in the doc you are using, because its on my paper copy.
As noted above, change the config file then cmcheckconf cmapplyconf
SEP
Owner of ISN Corporation
http://isnamerica.com
http://hpuxconsulting.com
Sponsor: http://hpux.ws
Twitter: http://twitter.com/hpuxlinux
Founder http://newdatacloud.com
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-14-2008 06:35 AM
тАО07-14-2008 06:35 AM
Re: Lock disk creation documentation
I am confused as to your answers since I stated that the hardware paths down to the i/o are identical. The lock pv device name is the same as it was on the system I moved from. Am I missing something?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-14-2008 06:40 AM
тАО07-14-2008 06:40 AM
Re: Lock disk creation documentation
root@xxxxxx$ cmcheckconf -v -C cluster.ascii
Checking cluster file: cluster.ascii
Checking nodes ... Done
Checking existing configuration ... Done
Gathering configuration information ... Done
Gathering configuration information ... Done
Gathering configuration information ..
Gathering storage information ..
Found 8 devices on node xxxxxx
Found 8 devices on node yyyyyy
Analysis of 16 devices should take approximately 2 seconds
0%----10%----20%----30%----40%----50%----60%----70%----80%----90%----100%
Found 7 volume groups on node xxxxxx
Found 6 volume groups on node yyyyyy
Analysis of 13 volume groups should take approximately 1 seconds
0%----10%----20%----30%----40%----50%----60%----70%----80%----90%----100%
.....
Gathering Network Configuration ......Abort(coredump)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-14-2008 07:12 AM
тАО07-14-2008 07:12 AM
Re: Lock disk creation documentation
check this:
https://forums11.itrc.hp.com/service/forums/questionanswer.do?threadId=1088044
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-14-2008 11:00 AM
тАО07-14-2008 11:00 AM
SolutionSecondly, you have to have the shared VG activated on the node on which you are going to do the cmcheckconf/cmapplyconf for it to be marked as a cluster lock disk.
I suspect there is something more substantially wrong here.
I would be inclined to consider taking a backup of teh /etc/cmcluster directoy on each node, try using cmquerycl to recreate a cluster ascii file as a test, then delete the cluster binary using either cmdeleteconf or simply remove the cmclconfig file on each node and see if cmcheckconf/cmapplyconf will now work.
also verify your patch versions of SG are at the very latest.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-16-2008 06:26 AM
тАО07-16-2008 06:26 AM
Re: Lock disk creation documentation
I do still have a package problem but I the main problem is past now.