- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: make_net_recovery restore problem
Categories
Company
Local Language
Forums
Discussions
Knowledge Base
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Forums
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-20-2006 07:05 PM
08-20-2006 07:05 PM
make_net_recovery restore problem
I have two rp3420,running 11.23. I have succesly taken the backup one system on anotehr by useing make_net_recovery. but when I try to restore from a make_net_recovery backup I am facing some problem.
The problem is when i run "search lan install" from PDC i am not getting any result.
even i tryed using boot lan.192.x.x.x insall, this is also failed.
both servers on same network and i am connected to servers by using the lan console.
can any one give clear stpes how to restore from the backup of make_net_recovery. I
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-20-2006 07:22 PM
08-20-2006 07:22 PM
Re: make_net_recovery restore problem
Did you configure ingite server (your second node )properly?.
Login to the ignite server and run
/opt/ignite/bin/ignite
In the GUI,select server setup and enter the required information.
Then try to boot the client.
sajeer
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-20-2006 07:29 PM
08-20-2006 07:29 PM
Re: make_net_recovery restore problem
Hi Sriman,
Check these links for more info.
http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=1044365
http://forums1.itrc.hp.com/service/forums/bizsupport/questionanswer.do?threadId=1020340
http://forums1.itrc.hp.com/service/forums/bizsupport/questionanswer.do?threadId=964539
http://forums1.itrc.hp.com/service/forums/bizsupport/questionanswer.do?threadId=1038138
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-20-2006 07:57 PM
08-20-2006 07:57 PM
Re: make_net_recovery restore problem
i just installed ignite s/w on server but i haven't configure it as ignite server (i.e, i didnt run server setup), but i configured it as server after i got this problem, then it is showing the clinet as make_net_recovery backup taken sucessfully in ignite server.
Is it required to configure the server before taking the backup ????
then i tried to restore, now it is showing the server in "sea lan insall" but when i boot from it, on the server the existing client is now showing as the new clinet.
how to select the backup location , once i booted from server
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-20-2006 09:26 PM
08-20-2006 09:26 PM
Re: make_net_recovery restore problem
Hi Sriman,
Not sure about this.I have to check it.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-21-2006 04:14 PM
08-21-2006 04:14 PM
Re: make_net_recovery restore problem
Below url should help you to understand more about ignite ux..
http://docs.fc.hp.com/en/5991-5320/ch05s10.html
http://www.docs.hp.com/en/B2355-90970/index.html
Best Regards,
Prashanth