Operating System - HP-UX
1832525 Members
8230 Online
110043 Solutions
New Discussion

[Q] HP-UX Install issue...

 
SOLVED
Go to solution
Su Ho Park
New Member

[Q] HP-UX Install issue...

Hi... HP-UX Power Users~!
I am trying to install hp-ux 11.0 & 11i on a hp rp5470 server.
But...installing fail...
Plase Advises...

System Config.
: rp5470, 750MHz CPU *2, 73GB Disk * 2
M/M is A5798, A6097 & A6098 on TEST!
---> CPU, Disk & Memory Testing Good!!!

Message...
[
Main Menu: Enter command or menu > sea

Searching for potential boot device(s)
This may take several minutes.

To discontinue search, press any key (termination may not be immediate).


Path# Device Path (dec) Device Path (mnem) Device Type
----- ----------------- ------------------ -----------
P0 0/0/1/1.2 intscsib.2 Random access media
P1 0/0/2/0.2 intscsia.2 Random access media
P2 0/0/2/1.2 Random access media


Main Menu: Enter command or menu > bo 0/0/2/1.2
Interact with IPL (Y, N, or Cancel)?> n

Booting...
Boot IO Dependent Code (IODC) revision 1


HARD Booted.

ISL Revision A.00.38 OCT 26, 1994

ISL booting hpux (;0):INSTALL

Boot
: disk(0/0/2/1.2.0.0.0.0.0;0):WINSTALL
8962064 + 1174208 + 1998104 start 0x278968


alloc_pdc_pages: Relocating PDC from 0xffff800000 to 0x7f9ab000.
WARNING: Could not open kernel symbol table
gate64: sysvec_vaddr = 0xc0002000 for 1 pages
NOTICE: nfs3_link(): File system was registered at index 4.

System Console is on the Built-In Serial Interface
Swap device table: (start & size given in 512-byte blocks)
entry 0 - auto-configured on root device; ignored - no room
WARNING: no swap device configured, so dump cannot be defaulted to primary swap.

WARNING: No dump devices are configured. Dump is disabled.
Starting the STREAMS daemons-phase 1
Create STCP device files
Starting the STREAMS daemons-phase 2
B2352B/9245XB HP-UX (B.11.00) #1: Wed Nov 5 22:38:19 PST 1997

Memory Information:
physical page size = 4096 bytes, logical page size = 4096 bytes
Physical: 12582912 Kbytes, lockable: 9833300 Kbytes, available: 11279136 Kby
tes

======= 07/20/01 17:18:23 EDT HP-UX Installation Initialization. (Fri Jul 20
17:18:23 EDT 2001)
@(#) Ignite-UX Revision B.2.6.3
@(#) install/init (opt) $Revision: 10.201.1.2 $
* EISA configuration has completed. Following the completion of a
successful HP-UX installation, please check the "/etc/eisa/config.err"
file for any EISA configuration messages.
* Scanning system for IO devices...
* Querying disk device: 0/0/1/1.2.0 ...
* Querying disk device: 0/0/2/0.2.0 ...
ERROR: funzip: Input not in "gzip" compressed format
ERROR: Could not uncompress libcfg.1.gz
NOTE: System rebooting...
]
13 REPLIES 13
Chris Wilshaw
Honored Contributor

Re: [Q] HP-UX Install issue...

from the uncompress errors, it looks like you may have faulty installation media. Do you have another CD that you can try?
Bill McNAMARA_1
Honored Contributor

Re: [Q] HP-UX Install issue...

I agree with Chris.
Everything up to that point look perfect for a cold install.

Later,
Bill
It works for me (tm)
Ravi_8
Honored Contributor

Re: [Q] HP-UX Install issue...

Hi,

Could be problem with media, try installing with another OS media
never give up
Su Ho Park
New Member

Re: [Q] HP-UX Install issue...

hmm...
i'm trying to install hp-ux 11.0 media five set & 11i media two set...
all media install fail...T.T
Su Ho Park
New Member

Re: [Q] HP-UX Install issue...

and...
same media install success on another system (k570)...
Jeff Schussele
Honored Contributor
Solution

Re: [Q] HP-UX Install issue...

Hi,

Well, if the media installs OK on other systems, then I'd suspect the DVD drive.
Double check the cabling, swap the drive with another machine if you have one.
But it sure sounds like the drive is not responding properly.

Rgds,
Jeff
PERSEVERANCE -- Remember, whatever does not kill you only makes you stronger!
Alan Casey
Trusted Contributor

Re: [Q] HP-UX Install issue...

Hi,

I had a problem not too different to this before, it turned out to be a Hardware problem and a HP engineer fixed it be resetting the SCSI devices, I'm not sure how this is done.

If you are able to boot from some other partition try running insf and then try the install again.


Otherwise, you might need to place a hardware call with HP.

Hope this is of help,
Alan
Paula J Frazer-Campbell
Honored Contributor

Re: [Q] HP-UX Install issue...

Hi

Down the server and reseat all cables and dvd/cd drive.

Clean the dvd/cd drive.

Try again.

If this fails replace the dvd/cd drive or "borrow" from another server.

Paula

If you can spell SysAdmin then you is one - anon
Su Ho Park
New Member

Re: [Q] HP-UX Install issue...

Oh...!
Thanks for regards yours...^^;
but i trying install ext. scsi DVD-ROM...
i met same message...--;
no disk error...not install...
T.T
Plase~~~
Bill McNAMARA_1
Honored Contributor

Re: [Q] HP-UX Install issue...

Post up the result of:

Main Menu: Enter command or menu > ser
Service Menu > IO

Later,
Bill
It works for me (tm)
Su Ho Park
New Member

Re: [Q] HP-UX Install issue...

Thank you all for your comments...!
I'll re-trying install on same system & same media...
but dvd-rom is ext. scsi...
oh~ starting installization...but error...T.T

messages 1>
NOTE: run_cmd: Process: 41 (funzip): killed by signal: 11.
ERROR: Could not uncompress libcfg.1.gz

* Loading configuration utility...
* Beginning installation from source: /dev/dsk/c0t2d0
======= 07/20/01 17:09:06 EDT Starting system configuration...
* Configure_Disks: Begin
* Will install B.11.00 onto this system.
* Creating LVM physical volume "/dev/rdsk/c1t2d0" (0/0/1/1.2.0).
* Creating volume group "vg00".
NOTE: run_cmd: Process: 67 (/sbin/vgcreate): killed by signal: 11.
ERROR: Command "/sbin/vgcreate -A n -e 4384 -l 255 -p 16 -s 16 /dev/vg00
/dev/dsk/c1t2d0" failed.

The configuration process has incurred an error, would you like
to push a shell for debugging purposes? (y/[n]):y
* Type "exit" to reboot, "exit 2" to ignore error
* Loading in /sbin/sh, please wait...
ksh: no memory: Not enough space
* Configure_Disks: Error
======= 07/20/01 17:10:30 EDT Installation complete: Failure
NOTE: Search for the word "ERROR" in the log file for details:
on a server: /var/opt/ignite/clients/0x00306E0CEB8F/install.log
on a client: /var/opt/ignite/local/install.log
NOTE: Rebooting system.

messages2>
ERROR: Tar: blocksize = 0; broken pipe?
ERROR: File: /sbin/fs/vxfs/mkfs not found.
ERROR: File: /sbin/fs/vxfs/newfs not found.
NOTE: loadfile: Process killed by signal: 11
loadfile command failed, retry? ([y]/n):

ERROR: directory checksum error
WARNING: Could not save patched version of pax.
WARNING: Could not make link to "usr/bin/hp9000s800": No such file or directory
(errno = 2).
WARNING: Could not make link to "usr/bin/hp9000s700": No such file or directory
(errno = 2).
* Download_mini-system: Warning
* Loading_software: Begin
ERROR: directory checksum error
ERROR: File: /sbin/fs/nfs/umount not found.
ERROR: File: /sbin/fs/nfs/mount not found.
NOTE: Retrying loadfile command...
ERROR: directory checksum error
* Installing boot area on disk.
Could not open /d_cfg_mnt_sb61/usr/lib/uxbootlf: No such file or directory
ERROR: Command "/d_cfg_mnt_sb61/sbin/mkboot -l -b
/d_cfg_mnt_sb61/usr/lib/uxbootlf /dev/rdsk/c1t2d0" failed.

The configuration process has incurred an error, would you like
to push a shell for debugging purposes? (y/[n]): * Loading_softw
are: Error
======= 08/14/02 23:06:12 EDT Installation complete: Failure
NOTE: Search for the word "ERROR" in the log file for details:
on a server: /var/opt/ignite/clients/0x00306E0CEB8F/install.log
on a client: /var/opt/ignite/local/install.log
NOTE: Rebooting system.


Please your advise...T.T
John Bolene
Honored Contributor

Re: [Q] HP-UX Install issue...

sounds to me like a disk problem with /dev/dsk/c1t2d0

the load is unable to write to this disk to do the vgcreate
It is always a good day when you are launching rockets! http://tripolioklahoma.org, Mostly Missiles http://mostlymissiles.com
Bill McNAMARA_1
Honored Contributor

Re: [Q] HP-UX Install issue...

either that or a serious memory problem..
what is the disk led status aroundf this timne.
It works for me (tm)