HPE GreenLake Administration
- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- "machinfo" is not working
Operating System - HP-UX
1834017
Members
2406
Online
110063
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Forums
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-21-2007 09:09 PM
05-21-2007 09:09 PM
"machinfo" is not working
Hi,
In my server "machinfo" is not working. I am running HP-UX B.11.23 on U 9000/800. I am able to do "man machinfo".
Please tell me how can i install "machinfo"
Thanks in advance
GSB
In my server "machinfo" is not working. I am running HP-UX B.11.23 on U 9000/800. I am able to do "man machinfo".
Please tell me how can i install "machinfo"
Thanks in advance
GSB
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-21-2007 09:20 PM
05-21-2007 09:20 PM
Re: "machinfo" is not working
Hi,
Try to find out where the comand is located
#whereis machinfo
So that you can give full path and run the command.seems to be the profile is not properly set.
Try to find out where the comand is located
#whereis machinfo
So that you can give full path and run the command.seems to be the profile is not properly set.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-21-2007 09:33 PM
05-21-2007 09:33 PM
Re: "machinfo" is not working
machinfo is only available for Integrity as the man page says:
Itanium(R)-Based Processor Family Only
Itanium(R)-Based Processor Family Only
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-21-2007 09:39 PM
05-21-2007 09:39 PM
Re: "machinfo" is not working
Hi,
As said above it is only avble on on Itanium.
You can use cstm or
/opt/ignite/bin/print_manifest on PA-RISC.
Regards.
As said above it is only avble on on Itanium.
You can use cstm or
/opt/ignite/bin/print_manifest on PA-RISC.
Regards.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
Company
Events and news
Customer resources
© Copyright 2025 Hewlett Packard Enterprise Development LP