Reboot failed after installing QPK1100

[Florian Wagner]

After Installing the QPK1100 December 2001 for HP-UX 11.00
I got the following error from the gsp of our L1000 (Processor PA-8500 440MHz, Firmware Revison 40.48):

Log Entry # 1 :
SYSTEM NAME: lds3gsp
DATE: 02/14/2002 TIME: 16:31:57
ALERT LEVEL: 3 = System blocked waiting for operator input

SOURCE: 1 = processor
SOURCE DETAIL: 1 = processor general SOURCE ID: 0
PROBLEM DETAIL: 0 = no problem detail

CALLER ACTIVITY: E = system warning STATUS: F
CALLER SUBACTIVITY: FF = implementation dependent
REPORTING ENTITY TYPE: E = HP-UX REPORTING ENTITY ID: 00

0xF8E000301100EFFF 00000000 0000EFFF type 31 = legacy PA HEX chassis-code
0x58E008301100EFFF 00006601 0E101F39 type 11 = Timestamp 02/14/2002 16:31:57


Log Entry # 2 :
SYSTEM NAME: lds3gsp
DATE: 02/14/2002 TIME: 16:31:54
ALERT LEVEL: 3 = System blocked waiting for operator input

SOURCE: 1 = processor
SOURCE DETAIL: 1 = processor general SOURCE ID: 0
PROBLEM DETAIL: 0 = no problem detail

CALLER ACTIVITY: E = system warning STATUS: 0
CALLER SUBACTIVITY: 00 = implementation dependent
REPORTING ENTITY TYPE: E = HP-UX REPORTING ENTITY ID: 00

0xF8E000301100E000 00000000 0000E000 type 31 = legacy PA HEX chassis-code
0x58E008301100E000 00006601 0E101F36 type 11 = Timestamp 02/14/2002 16:31:54


Log Entry # 3 :
SYSTEM NAME: lds3gsp
DATE: 02/14/2002 TIME: 16:31:42
ALERT LEVEL: 12 = Software failure

SOURCE: 1 = processor
SOURCE DETAIL: 1 = processor general SOURCE ID: 0
PROBLEM DETAIL: 0 = no problem detail

CALLER ACTIVITY: B = system panic STATUS: 0
CALLER SUBACTIVITY: 00 = implementation dependent
REPORTING ENTITY TYPE: E = HP-UX REPORTING ENTITY ID: 00

0xA0E000C01100B000 00000000 000005E9 type 20 = major change in system state
0x58E008C01100B000 00006601 0E101F2A type 11 = Timestamp 02/14/2002 16:31:42



Log Entry # 4 :
SYSTEM NAME: lds3gsp
DATE: 02/14/2002 TIME: 16:31:42
ALERT LEVEL: 12 = Software failure

SOURCE: 1 = processor
SOURCE DETAIL: 1 = processor general SOURCE ID: 0
PROBLEM DETAIL: 0 = no problem detail

CALLER ACTIVITY: B = system panic STATUS: 0
CALLER SUBACTIVITY: 80 = implementation dependent
REPORTING ENTITY TYPE: E = HP-UX REPORTING ENTITY ID: 00

0xF8E000C01100B800 00000000 0000B800 type 31 = legacy PA HEX chassis-code
0x58E008C01100B800 00006601 0E101F2A type 11 = Timestamp 02/14/2002 16:31:42


With the newly build kernel form the QPK it is not possible to boot the kernel.
Luckily the old kernel works.
What is the reason? Any ideas to fix the problem?

Thanks,
F. Wagner

[Bill McNAMARA_1]

I would imagine it's something to do with PHKL_18543

in any case, you may have needed to install the XSHWCR____ before the QPK.

Did you read the release notes!
I installed that recently, but installed on top of a Sept 2001 clean install and had no problems (apart from a reflectionX telnet issue - need to add a telnet patch after.)

Later,
Bill