- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Replace HBA card using sam remove/add option
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-02-2012 07:00 AM
08-02-2012 07:00 AM
Replace HBA card using sam remove/add option
Has anyone tried replacing a bad HBA fiber card using sam remove/add option? HP-UX 11.11
OLRAD is on 11.23 and 11.31. But is it available for 11.11?
- Tags:
- HBA
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-10-2012 01:37 AM
10-10-2012 01:37 AM
Re: Replace HBA card using sam remove/add option
on 11.31 it works like this:
notice to WWPN (world wide port numbers) that will be changes after the change of the hba:
root@mybox:~# fclputil /dev/fclp2 # or fcdutil /dev/fcd1
Vendor ID is = 0x10df
Device ID is = 0xfe00
PCI Sub-system Vendor ID is = 0x103c
PCI Sub-system ID is = 0x7046
Chip version = 2
Firmware Version = 2.82X4 SLI-3 (Z3D2.82X4)
EFI Version = ZE3.21A3
EFI Boot = ENABLED
Driver-Firmware Dump Available = NO
Driver-Firmware Dump Timestamp = N/A
Previous Topology = UNINITIALIZED
Link Speed = 4Gb
Local N_Port_id is = 0x820090
Previous N_Port_id is = None
N_Port Node World Wide Name = 0x5001438010631b47
N_Port Port World Wide Name = 0x5001438010631b46
Switch Port World Wide Name = 0x2069000dec446e80
Switch Node World Wide Name = 0x2001000dec01de81
Driver state = AWAITING_LINK_UP
Hardware Path is = 0/6/0/0/0/0/2/0/0/0
Maximum Frame Size = 2048
Driver Version = @(#) FCLP: PCIe Fibre Channel driver (FibrChanl-02), B.11.31.1009, May 7 2010, FCLP_IFC (3,2)
root@mybox:~#find out slot_ID of HBA-Card to change usinf cstm.
Prepare to replace the HBA:
# /usr/bin/olrad -r slot_ID
The above command performs a Critical Resource Analysis (CRA).
Replace the HBA with a new compatible HBA of similar type in the same slot.
Bring the replaced HBA back into the configuration. Enter the following:
# /usr/bin/olrad -q
Enter the following command after you replace the HBA:
# /usr/bin/olrad -R slot_ID
Verify the success of the operation. The slot power should be ON, driver is OLAR capable, and so on.
# /usr/bin/olrad -q slot_ID
Perform an operating system device scan to re-discover the LUNs. Enter the following:
# ioscan -fn
Lookup new WWPNs using fclputil or fcdutil; then update zoning to use new WWPN.