Restore Ignite "system panic"

[David Islas González_1]

Hi everybody, I'm trying to change my rp7410 box with an rp4440. I made an Ignite tape from the rp7410 and I'm trying to restore it on my rp4440.

1. I was working with an EVA3000, now I'm getting connected to an XP.
2. I have a Service Guard cluster running on it.
3. I'm just trying to get vg00 where my hpux and my applications are installed. Then I will restore data with DP.
4. When I restore on the rp4440. I'm getting the next system panic:

Boot
: disk(0/1/1/1.0.0.0.0.0.0;0)/stand/vmunix
10878976 + 1851392 + 24149560 start 0x1fbfe8




alloc_pdc_pages: Relocating PDC from 0xfffffff0f0c00000 to 0x3f900000.



Firmware Version 46.34

Duplex Console IO Dependent Code (IODC) revision 1



Stored message buffer up to panic:
gate64: sysvec_vaddr = 0xc0002000 for 2 pages
NOTICE: autofs_link(): File system was registered at index 3.
NOTICE: cachefs_link(): File system was registered at index 5.
NOTICE: nfs3_link(): File system was registered at index 6.
CPQswsp : Persistence error [error code : 2]. Cause: Unknown. Failed to retrieve the preferred path persistent data for all the LUNs
of the Array 50001FE150019050. This may result in loss of preferred path settings of the LUNs under this Array. Ignore th
is message if all the LUNs of this Array are deleted or if none of the LUNs of this Array have preferred path settings.
255/255 swspBus
0 sba
0/0 lba
0/0/1/0 asio0
0/0/1/1 asio0
0/0/2/0 hcd
0/0/2/0.1 hub
0/0/2/1 hcd
0/0/2/1.1 hub
0/0/2/2 ehci
0/0/3/0 side_ba
0/0/3/0.0 side
0/0/3/0.0.0 tgt
0/0/3/0.0.0.0 sdisk
0/0/3/0.0.7 tgt
0/0/3/0.0.7.0 sctl
0/0/3/0.1 side
0/0/3/0.1.7 tgt
0/0/3/0.1.7.0 sctl
0/1 lba
0/2 lba
0/4 lba
I/O hardware probe timed out at path 0/4/2/0

System Panic:

linkstamp: Wed Mar 14 17:13:02 EST 2007
_release_version: @(#) $Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c 'Vw for CUPI80_BL2000
_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108' Wed Nov 8 19:24:56 PST 2000 $
panic: I/O system hang

PC-Offset Stack Trace (read across, top of stack is 1st):
0x002549e0 0x003ce968 0x0092136c
0x0003fa10 0x002a8d8c 0x00169764
0x0042189c 0x0041b804 0x00418cac
0x003cff8c 0x003cfb6c 0x003cfed4
0x003cfb6c 0x003cfed4 0x003cfb6c
0x003d02ec 0x003d3c60 0x004b6584
0x0039e1e0 0x00177a2c 0x001fc5e4
End Of Stack



*** A system crash has occurred. (See the above messages for details.)
*** The system is now preparing to dump physical memory to disk, for use
*** in debugging the crash.

ERROR: Your system crashed before I/O and dump configuration was complete.
A crash dump cannot be taken under these circumstances without
special configuration. Contact your HP support representative.

[Patrick Wallek]

Ignite can work well with similar model machines, but an rp7410 to an rp4440 is probably too different for this to ever work.

You will probably have much more luck by just installing the OS from scratch. This affords you the opportunity to go to the latest version of HP-UX, 11iv2 (11.23) or if you are really cutting-edge, 11iv3 (11.31), and to get all the latest patches installed.

[Sandy Chen]

Hi,

Can you tell us your current patch bundle on the rp7410? Make tape recovery is not supported for different hardware, but it could be running, fyi that rp4440 requires at least Dec '04 patch bundles installed

Regards,
Sandy