1833762 Members
2757 Online
110063 Solutions
New Discussion

Samba 3.0.10 on HPUX 11i

 
SOLVED
Go to solution
Simeon Harwood
Regular Advisor

Samba 3.0.10 on HPUX 11i

Afternoon all,
I've been trying to get Samba working on HPUX, but can't get the daemons running.
I've downloaded the following packages: -
Samba 3.0.10
libiconv 1.9.2
openldap 2.2.20
openssl 0.9.7e
All of them in depot format. I've installed them via swinstall with no errors.
I try and start the smbd daemon, and ended up with the following errors: -
dld.sl can't access: -
liblber.sl.2 and libldap.sl.2

So I nicked these 2 files from the Apache install that I had, and put them in the correct place.
Now when I try and start the daemon, I get nothing at all, no error message, no entry in syslog to say why it didn't start, and no smbd daemon running.
I can get into swat to have a look at the configuration, and can edit smb.conf via SWAT, or from command line. This works fine, I can run the testparam prog OK with no errors.

I just cant seem to get the daemons running.

Anyone got any advice on what might be wrong, or somthing that I might have miseed.

You never had this problem with a pencil and paper!
7 REPLIES 7
Geoff Wild
Honored Contributor

Re: Samba 3.0.10 on HPUX 11i

What is in /var/opt/samba/log.smbd and log.nmbd?

Did you install the HP version?

http://software.hp.com/portal/swdepot/displayProductInfo.do?productNumber=B8725AA

Rgds...Geoff
Proverbs 3:5,6 Trust in the Lord with all your heart and lean not on your own understanding; in all your ways acknowledge him, and he will make all your paths straight.
Simeon Harwood
Regular Advisor

Re: Samba 3.0.10 on HPUX 11i

No I didn't install the HP version. We are doing a project here that requires a minimum samba version of 3.x and the HP one is 2.2.8a
Because of this, I don't have a log file in /var or /opt, as the whole install tree is under /usr/local/samba

I've been looking for a log file but can't find one. (very frustrating!!!)
I've just tried the HP version to see if it works, to make sure that everything else is OK, and it works fine. But the problem is this is not supported under our project.
Any clues?
You never had this problem with a pencil and paper!
Geoff Wild
Honored Contributor

Re: Samba 3.0.10 on HPUX 11i

Actually - the latest HP one is Samba 3.07....

As far as logs, what is in your smb.conf file?

Does swat work?

http://yourserver:901

Rgds...Geoff
Proverbs 3:5,6 Trust in the Lord with all your heart and lean not on your own understanding; in all your ways acknowledge him, and he will make all your paths straight.
Simeon Harwood
Regular Advisor

Re: Samba 3.0.10 on HPUX 11i

Ah, yes I've just seen that the new HP version is 3.07. I'm going to try that. I've got the 2.2.8a version working, so if i get the new version of that, I might be able to get that one working too.

The smb.conf file was prity basic. I stated off with not having one, and using SWAT (port 901) to configure a basic setup.

Think I've given up with the version of Samba that I down loaded, it just dosen't seem to work on HP. I've had it working on Linux just fine.
You never had this problem with a pencil and paper!
Geoff Wild
Honored Contributor
Solution

Re: Samba 3.0.10 on HPUX 11i

Also try:

testparm /etc/samba/smb.conf

I think that is default location from samba.org....

Rgds...Geoff
Proverbs 3:5,6 Trust in the Lord with all your heart and lean not on your own understanding; in all your ways acknowledge him, and he will make all your paths straight.
Simeon Harwood
Regular Advisor

Re: Samba 3.0.10 on HPUX 11i

yeah, I've tried the testparam and this worked OK.
I've given up with the downloaded version of Samba,It just dosn't work on HPUX.
I'll grab the new version of CIFS.
Thanks for the help.

Sime.
You never had this problem with a pencil and paper!
Simeon Harwood
Regular Advisor

Re: Samba 3.0.10 on HPUX 11i

downloaded the new version of CIFS for software.hp.com
You never had this problem with a pencil and paper!