HPE GreenLake Administration
- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Serial Port for Console, Remote & UPS
Operating System - HP-UX
1829863
Members
2277
Online
109993
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Forums
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-15-2006 07:22 AM
11-15-2006 07:22 AM
I have connected my RX3000 UPS to the serial port marked UPS, which is attached to PCI card on the back of my rp5470. For LanSafe and PowerMonitor I need to know the tty of the port plugged into the UPS. When I install PowerMonitor it cannot auto-detect the port and offers me a choice of tty0p0, tty0p1, tty0p2, or tty0p4.
Here's what ioscan says about the card:
tty 0 0/0/4/1 asio0 CLAIMED INTERFACE PCI Serial (103c1048)
/dev/GSPdiag1 /dev/mux0 /dev/tty0p1 /dev/tty0p4
/dev/diag/mux0 /dev/tty0p0 /dev/tty0p2
How can I determine which tty is connected to the UPS?
Much Thanks!
Points Awarded!
Brad
Here's what ioscan says about the card:
tty 0 0/0/4/1 asio0 CLAIMED INTERFACE PCI Serial (103c1048)
/dev/GSPdiag1 /dev/mux0 /dev/tty0p1 /dev/tty0p4
/dev/diag/mux0 /dev/tty0p0 /dev/tty0p2
How can I determine which tty is connected to the UPS?
Much Thanks!
Points Awarded!
Brad
It's not impossible -- it'll just cost more...
Solved! Go to Solution.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-15-2006 07:37 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-15-2006 07:42 AM
11-15-2006 07:42 AM
Re: Serial Port for Console, Remote & UPS
Thanks Yang, there it was!
It's not impossible -- it'll just cost more...
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
Company
Events and news
Customer resources
© Copyright 2025 Hewlett Packard Enterprise Development LP