still i have problem with my guest on IVM

[Slawek Ksiazek]

when i boot IVM guest on rx7640 i have following message:


MCA[1]:MCA occurred!!!.
MCA[1]: lid 0x1010000
MCA[1]: iip 0xea080000000a0c00, ipsr 0x1008228012, ifa 0xea080000000beec0
MCA[1]: xip 0xea080000000beec0, xpsr 0x10100822a012, xfs 0x0
MCA[1]:The processor state register value = 0x80010000fff21120
MCA[1]:Rendezvous status information GR11 = 2
MCA[1]:mca_wakeup() procs MCA'ed 1, procs rendezvous'ed 6,
procs INIT'ed 1, procs not rendezvoused 0.
MCA, IIP:0xea080000000a0c00 IFA:0xea080000000beec0

after this my system dump and restart HOST, where is problem,if problem is hardware or software? Please help me,

Slawek

[Torsten. · Accepted solution]

I think it is OK now:

http://forums11.itrc.hp.com/service/forums/questionanswer.do?threadId=1269799

Not?

I'm not sure how related it is, but the OS type for this VM is UNKNOWN ... adjust this!

[Slawek Ksiazek]

not :( i stll have the same problem with booting my guest on IVM last version HPUX 11v3 and also HPUX 11v2,during booting guest with HPUX 11.31 my host dump and restart
I don't know where is problem, Please help me.


Slawek

[Torsten.]

First I would set the OS type:

# hpvmmodify -P -O hpux

[Slawek Ksiazek]

I had set OS on HPUX

Slawek

[Torsten.]

Does the host or the guest crash? This is not clear to me.

[Slawek Ksiazek]

during boot guest my host crash

[Torsten.]

Ooops ... what disk did you configure for the guest? Is it used by the host already?

Check for patches:

http://www.itrc.hp.com/service/patch/patchDetail.do?patchid=PHKL_37812&sel={hpux:11.23,}&BC=main|search|

http://www.itrc.hp.com/service/patch/patchDetail.do?patchid=PHSS_37845&sel={hpux:11.23,}&BC=main|search|

Better to do a patch assessment in ITRC.

[Slawek Ksiazek]

I configured differently my disk on guest

hpvmconfigure -a
disk:scsi::lv:/dev/vg01/rlvol01

or

disk:scsi:0,0,0:disk:/dev/rdsk/c5xxx -a

hpvmdevmgmt -m gdev:/dev/rdsk/c5xxx:attr:SHARE=YES

I try install on gest HPUX 11.31 FOE relase March2008 or HPUX 11.23 FOE June2008

hpvminfo give me version 3.5

Slawek

[Torsten.]

You posted a config on your previous thread, but the current is likely completely different.

I don't know your config.

You share the disk? Between what?

[Slawek Ksiazek]

Now I have set share=yes but I'am not share disk but I try diferently options with configuration guest, because I try solve me problem

Slawek

[Torsten.]

more patches and software:

PHSS_37312
PHSS_37306

http://h20392.www2.hp.com/portal/swdepot/displayProductInfo.do?productNumber=AVIO

http://h20392.www2.hp.com/portal/swdepot/displayProductInfo.do?productNumber=HostAvioLan

http://h20392.www2.hp.com/portal/swdepot/displayProductInfo.do?productNumber=HostAVIOStor

Do you have them all?

[Slawek Ksiazek]

AVIO lan and store i have in version 0806, i try install new version AVIO 0808 and also patches

[Torsten.]

Patches are important!

:

PHSS_37845: PANIC HANG CORRUPTION
This patch addresses a number of potential host and guest panics and hangs.

[Slawek Ksiazek]

i see in description about patch information:

10: Defect QXCR1000745374 QXCR1000744790 QXCR1000745372
QXCR1000574383 QAR0003326
Guests running Mar-2008 and later versions of HP-UX 11v3
may cause a VM Host panic with the following:
System Panic: Fault when executing in kernel mode
Stack Trace:
Function Name
bad_kern_reference+0xa0
$cold_pfault+0x510
vm_hndlr+0xd40
bubbledown+0x0
ptaccget+0x221
checkaccess+0x160
hdl_pfault+0x3a0
pfault+0x200
vm_hndlr+0xd40
bubbledown+0x0
End of Stack Trace

I send you info after instalation this patches, Thank you


Slawek

[Slawek Ksiazek]

Now all works ok, patch solved all problems, Torsten you have right,Thanks a lot for involvement :o)


Slawek

[Torsten.]

good news. You are welcome.

[Slawek Ksiazek]

You are the Best!

Slawek

[Slawek Ksiazek]

Hi Torsten,

Believe me i have still problem with runining and install guest (HPUX 11.31,and HPUX 11.23), exacltly this same information, and after this host dump and restart

Slawek

[Gokul Chandola]

HI,
If you are facing same problem again then why not you have to Contact to HP for Any Hardware related issue to conform.
That may be minor.

Regards,
Gokul Chandola

[Slawek Ksiazek]

what you think?

http://forums11.itrc.hp.com/service/forums/questionanswer.do?threadId=1270945

[Slawek Ksiazek]

I open call in HP, classification broken cpu 0 or cpu 3 or cell 1 :o)

[Slawek Ksiazek]

Hi I.d like inform that problem was resolved, today i get unofficial patch on this my problem,problem was only software.Slawek