UNCLAIMED device (PCI Display and SerialBus)

[Gian Filippo]

Hi all,
I have just installed a PCI 2D graphic and 2 port USB adapter on a rp2470 machine with HP-UX 11.11.
When run ioscan I got the following output:
unknown -1 0/2/0/0 UNCLAIMED UNKNOWN PCI Display (10
3c108b)
unknown -1 0/6/2/0 UNCLAIMED UNKNOWN PCI SerialBus (
1045c861)
In my understanding this should mean that I need the drivers.
Someone could help me to understand where I can find the drivers? How can I install them?
I have the HP-UX 11.11's CDs can I use them?

Thank you very much for any help...
Gian Filippo

[Slawomir Gora]

Hi,

you can look for drivers on Applicatin CD
(look for names corresponding to P/N)

[Steven E. Protter]

You are correct. You need drivers.

If this product is hp certified hardware, there should be drivers on the Core OS cd for it. It not, you may need to get HP-UX drivers from the card manufacturer.

AGain, if this device is supported, you may find drivers for it in one of the following locations:

http://software.hp.com

Patch database:
http://www1.itrc.hp.com/service/patch/mainPage.do

SEP

[Gian Filippo]

Hi all,
the the graphic card is A6150B
PCI 2D Graphics and 2 port USB Adptrs.
It is a device supported by HP but I'm not able to find the Driver.

Someone can help me??
Thank you

[Fred Ruffet]

You may be interrested in this thread on hardware installation :
http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=573396

and this one :
http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=62779
seems to say you need graph3 driver loaded.

Regards,

Fred

[Stf]

Hello,

try this:
go to sam->kernel configuration->drivers
and add thes drivers : hcd, hid, hub, usbd for usb and graph3 for graphics.

Stf ;-)

[Slawomir Gora · Accepted solution]

Hi,

The graphics card is only supported in PCI slot 1 (above console and lan port),
the half-length, independent PCI slot;
the USB card is supported in any slot

After that install by SAM drivers for
1. graph3, usbd, hcd, hid, hub

SAM->Kernel Configuration->Drivers
Select drivers by space -> Menu Actions-> Add to Kernel
and then Process New Kernel (this will reboot your server)

[Steven E. Protter]

Most HP graphics cards are already built in. After putting the driver status in the kernel to IN you need to use action, process new kernel.

A boot will be required.

Such drivers should be on the Core OS CD if not installed. I've sometimes seen them distributed in the patch database.

SEP

[Gian Filippo]

I all,

finally I have linked the driver into the kernel and when I run the ioscan I get:
graphics 0 0/2/0/0 graph3 CLAIMED INTERFACE PCI Display (103c108b)

but the monitor seems not working:
it is black.
Any idea???

Gian Filippo

[Stf]

When you had reboot the server it dosen't switch to the graphic monitor?

Stf

[Gian Filippo]

Yes,
after the reboot the server switched to the the graphic monitor, but it remains blank.

Thank you

[Stf]

Have you install the CDE environment?
check with:

# swlist

[Gian Filippo]

yes,
the CDE is installed.

[Stf]

check the /etc/rc.config.d/desktop file :
it must be:
DESKTOP=CDE

Stf

[Gian Filippo]

yes it is.

[Fred Ruffet]

If you want to run X on this screen at startup, you may have to configure /etc/X11/XF86config.

Regards,

Fred