- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: USB Serial ports cu on rx2800
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-18-2011 09:15 PM
тАО04-18-2011 09:15 PM
Re: USB Serial ports cu on rx2800
...
Each controller has the following factory-default IP settings:
- DHCP: enabled
- Controller A IP address: 10.0.0.2
- Controller B IP address: 10.0.0.3
- IP subnet mask: 255.255.255.0
- Gateway IP address: 10.0.0.1
...
Each controller model has these management ports, no matter if it is iscsi, FC or a mix of both.
Page 45 of the user manual has also the settings of the serial (USB) ports:
Table 6
Terminal emulator display settings
Parameter Value
Terminal emulation mode VT-100 or ANSI (for color support)
Font Terminal
Translations None
Columns 80
Table 7
Terminal emulator connection settings
Parameter Value
Connector COM1 (typically)
Baud rate 115,200
Data bits 8
Parity None
Stop bits 1
Flow control None
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-18-2011 09:32 PM
тАО04-18-2011 09:32 PM
Re: USB Serial ports cu on rx2800
> - DHCP: enabled
> - Controller A IP address: 10.0.0.2
> - Controller B IP address: 10.0.0.3
> [...]
So, if it hears from a DHCP server, what
happens to the 10.0.0.x addresses?
Overridden by the DHCP-server info?
Of course, I also don't know if there's a
DHCP server available in this environment,
but that might explain why no one responds at
10.0.0.x.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-18-2011 09:41 PM
тАО04-18-2011 09:41 PM
Re: USB Serial ports cu on rx2800
- PC with DHCP server (cross cable) -> the controller get a custom IP
- PC without DHCP server (cross cable) -> controller is accessible via 10.0.0.x)
- PC with USB connection using putty serial terminal emulator for accessing the serial CLI
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-04-2021 05:42 PM
тАО11-04-2021 05:42 PM
Re: USB Serial ports cu on rx2800
Actually most CISCO and these newer disk arrays DO have a built in USB to SErial port converter
Literally connecting the port to the USB connection on a PC installs the driver to make the USB connection a soft serial port and it works well
I am looking for supported USB to Serial Port cable adapters such as the Digi Edgeport/1 for HP-UX
Does anyone know if this is supported on HP-UX on rx2800??? It is on VMS but I know little abou HP-UX compatibility
I mean, I know that the onboard MP/Serial works so I am guessing finding a PCI-e card with the same chipset for serial console should work right?????
David
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-04-2021 05:45 PM
тАО11-04-2021 05:45 PM
Re: USB Serial ports cu on rx2800
Torsten
Do you know if ANY PCI-e or USB to Serial port converters or card ARE supported under HP-UX 11.31 on HPE Integrity rx2800?
I am guessing it comes down to chipsets. I mean, there must be a card that would be identified by HP-UX
DO you know what chipset is used by the rx2660 as this has 2 serial ports built in
DT
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-06-2021 10:04 AM
тАО11-06-2021 10:04 AM
Re: USB Serial ports cu on rx2800
Hi David,
I am not aware of any USB to Serial port converter which is supported under HP-UX.
PCI card A6748A (8-port Mux) may help but I am not sure if it available anymore.
Refer support.hpe.com/hpesc/public/docDisplay?docLocale=en_US&docId=c02017129
Regards
Manish
- « Previous
- Next »