HPE GreenLake Administration
- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Veritas Netbackup : which tape mounted?
Operating System - HP-UX
1827593
Members
2608
Online
109965
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Forums
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-23-2004 08:57 PM
06-23-2004 08:57 PM
Veritas Netbackup : which tape mounted?
hi,
how can I detect which tape is currently loaded in a standalone tape drive?
thanks in advance,
netbackup newbie :(
how can I detect which tape is currently loaded in a standalone tape drive?
thanks in advance,
netbackup newbie :(
All unix flavours are exactly the same . . . . . . . . . . for end users anyway.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-24-2004 12:18 AM
06-24-2004 12:18 AM
Re: Veritas Netbackup : which tape mounted?
hi,
no knowledge of netbackup, but using mc command, you will also be able to tell which tape is currently loaded:
# mc -p DS
if the slot is EMPTY and drive, i.e. DT_slot_# is FULL, then the empty slot is where your tape comes from.
regards.
no knowledge of netbackup, but using mc command, you will also be able to tell which tape is currently loaded:
# mc -p
if the slot is EMPTY and drive, i.e. DT_slot_# is FULL, then the empty slot is where your tape comes from.
regards.
what you do not see does not mean you should not believe
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-24-2004 08:50 AM
06-24-2004 08:50 AM
Re: Veritas Netbackup : which tape mounted?
Thierry -
The netbackup activity monitor==> right click on the job==> open the details tab.
Should show you the tape # that was mounted and each successive tape if it is a multi tape backup.
Best regards,
dl
The netbackup activity monitor==> right click on the job==> open the details tab.
Should show you the tape # that was mounted and each successive tape if it is a multi tape backup.
Best regards,
dl
"I'm not dumb. I just have a command of thoroughly useless information."
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
Company
Support
Events and news
Customer resources
© Copyright 2025 Hewlett Packard Enterprise Development LP