1820116 Members
3173 Online
109619 Solutions
New Discussion юеВ

Re: Xserver

 
SOLVED
Go to solution
Fayez
Trusted Contributor

Xserver

Hi all,
We have rx660 with hp-ux 11.31 installed,my question is where is the dt command???
in smh it gives that xserver is not running

if any one can help please....
11 REPLIES 11
Torsten.
Acclaimed Contributor
Solution

Re: Xserver

AFAIR the cde environment is not installed per default. Check with swlist. Install from the DVD set if needed.

> in smh it gives that xserver is not running

What are you trying to do from smh?
Executing an X application?

In this case you need to run a Xserver locally (on your PC).

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Fayez
Trusted Contributor

Re: Xserver

I checked it with swlist and it is there
the output:

CDE B11.31 HP-UX CDE User Interface
Torsten.
Acclaimed Contributor

Re: Xserver

And what are you trying to do ... ?

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Fayez
Trusted Contributor

Re: Xserver

I want to enable the graphical login,
so I need the dtconfig and dtlogin commands.

in smh (test mode) I tried to see the monitor settings and it gives in the header of the page No X server is running.
Torsten.
Acclaimed Contributor

Re: Xserver

> I want to enable the graphical login

Where?
Over the network?
Using what emulation?

Find the files:

# whereis dtlogin

But this is probably not what you (should) looking for.

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Fayez
Trusted Contributor

Re: Xserver

I want to enable it on both local monitor
and over network

and I already search for dtlogin command and I found nothing...

thanks..
Torsten.
Acclaimed Contributor

Re: Xserver

In a default setup, the local VGA is just dark. The default console is the serial port (over MP/iLO) and you should NOT change this.

To enable the local monitor as a X terminal, try this:

(I did not try this on 11.31, but on 11.23)

Check /etc/dt/config/Xservers.
If last line is commented out as follows:

# * Local local@console /usr/bin/X11/X :0

remove '# ' and restart dtlogin:

# /sbin/init.d/dtlogin.rc stop
# /sbin/init.d/dtlogin.rc start

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Fayez
Trusted Contributor

Re: Xserver

My problem is all of these files is missing
I did it with ver 11.23 and it works
but in this version I could not..

Is these commands changed ???
Robert-Jan Goossens_1
Honored Contributor

Re: Xserver

Fayez
Trusted Contributor

Re: Xserver

Thanks for all,

I found the missing :

English-CDE.
It is strange but any way it solve the problem.
Thanks again...
Fayez
Trusted Contributor

Re: Xserver

Thanks .....