ioscan lookalike for Linux

[Bernhard Mueller]

Hello,

as an HP-UX man I would like to know, if there is something similar to ioscan in any Linux distri.
Or perhaps at least something like prtdiag under Solaris...

Regards,
Bernhard

[Tom Ward_1]

A check of google found
/sbin/lspci -v

It's not bad but it doesn't show disks. It a bit like Solaris prtdiag.

[Martin P.J. Zinser]

Hello Bernhard,

are you thinking about something like this:

zinser@bibo:~> /sbin/lspci -v

00:00.0 Host bridge: VIA Technologies, Inc. VT8601 [Apollo ProMedia] (rev 05)
Flags: bus master, medium devsel, latency 0
Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities:

00:01.0 PCI bridge: VIA Technologies, Inc. VT8601 [Apollo ProMedia AGP] (prog-i)
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: f4100000-f57fffff

00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 2)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Flags: bus master, stepping, medium devsel, latency 0

00:07.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus Master)
Flags: bus master, medium devsel, latency 64
I/O ports at 1460 [size=16]
Capabilities:

00:07.2 USB Controller: VIA Technologies, Inc. USB (rev 10) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Flags: medium devsel, IRQ 10
I/O ports at 1440 [size=32]
Capabilities:


[...]

Greetings, Martin

[Huc_1]

Not that I know, but

Under the /proc directory you will find all sort of information about loaded device and much more try

cat /proc/scsi/scsi
cat /proc/iomem
cat /proc/irq

etc..

Just be cautious about writing in /proc specialy if you are priviledged.

J-P

[Bernhard Mueller]

Thanks for the responses so far.

Actually, I was more looking for something to find out whether or not the machine can see and use devices such as LUNs on a dis array when I connect it to a fibre channel switch and put the WWN of its FC adapter into a storage zone.

Regards,
Bernhard

[Huc_1]

Try

#cdrecord -scanbus

J-P

[Paul Cross_1]

here is a cut and paste from the UNIX rosetta stone...

dmesg (if you're lucky)
/proc/*
lspci
(SuSE) hwinfo

[James A. Donovan]

What LUN's your particular HBA sees will be recorded under /proc/scsi//X

where X is some number...

e.g. my QLogic SCSI HBA sees 5 LUN's on my EMC frame.

$ cat /proc/scsi/qla2300/2
.
.
.
SCSI LUN Information:
(Id:Lun)
( 0: 0): Total reqs 1, Pending reqs 0, flags 0x0*, 0:0:81,
( 0: 1): Total reqs 14306183, Pending reqs 0, flags 0x0, 0:0:81,
( 0: 2): Total reqs 25, Pending reqs 0, flags 0x0, 0:0:81,
( 0:240): Total reqs 146, Pending reqs 0, flags 0x0, 0:0:81,
( 0:241): Total reqs 80, Pending reqs 0, flags 0x0, 0:0:81,

[Karthik S S]

cdrecord --scanbus

-Karthik S S

[Paul Cross_1 · Accepted solution]

I just checked out hwscan and hwinfo under suse. Very very useful. I haven't tried it under any other distro though. I just thought I'd add in in case you were looking at using SuSE.

[Bernhard Mueller]

hwinfo & hwscan seem indeed SUSE specific but the most useful tools.

Regards,
Bernhard

[Thomas_18]

you may try :
#lshw
for general hardware purpose
#scsiadd
For LUN scanning

Both are on Debian or a simple google search.