- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- decnet phase IV issue with set host
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-07-2011 09:25 AM
тАО06-07-2011 09:25 AM
I have a 2 nodes ovms 8.3 integrity in 2 diferent networks.
yesterday change a cisco switch 6500, this working in layer 3.
When try conect via I64VMS DECNET_PHASE_IV V8.3 is not successfull.
$set host walli
%SYSTEM-F-UNREACHABLE, remote node is not currently reachable
but via telnet,ftp,ssh no problem.
my routing table is fine.
Some one know if is necesary a patch o configuration in my decnet?
also for snap (availability manager) dont work.
any help?
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-07-2011 09:48 AM
тАО06-07-2011 09:48 AM
SolutionDECnet Phase IV is not based on IP.
Cisco switches are very fond of IP, and less fond of other protocols, and Cisco support folks can have similar proclivities. It is quite possible to encounter network engineers that have no experience with non-IP protocols, for that matter.
Your Cisco support folks will want to and need to review the switch configuration, as is typical of these cases.
Chances are, the Cisco folks will need to open a VLAN for transmission of Ethernet traffic involving Ethernet protocols other than IP ("bridging" or whatever Cisco calls it), or to configure and enable DECnet routing within the switch, depending on the particular details of the network.
If your Cisco folks are unable or unwilling to open up connections for protocols other than IP, then you're left to migrate your OpenVMS boxes to DECnet-Plus and switch to DECnet over IP, or to migrate away from the DECnet protocols entirely.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-07-2011 08:07 PM
тАО06-07-2011 08:07 PM
Re: decnet phase IV issue with set host
MC NCL flush session control naming cache entry "*"
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-08-2011 03:10 AM
тАО06-08-2011 03:10 AM
Re: decnet phase IV issue with set host
Edgar is using DECNET Phase IV, and not DECNET_OSI. NCL commands are not appropriate here.
Duncan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-08-2011 04:49 AM
тАО06-08-2011 04:49 AM
Re: decnet phase IV issue with set host
Much apreciated for your time