- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Re: fetching data from server using SNMP trap in O...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-26-2007 12:24 AM
тАО02-26-2007 12:24 AM
fetching data from server using SNMP trap in Open VMS 7.2
I need to pull some selected from one of my servers on open VMS 7.2, using SNMP trap? I am using SNMP_traprcv -d -p 1024 command, but after that system gets hang and almost no response.
Pls let me know the procedure for this process?
Regards,
Amit Phadnis.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-26-2007 01:36 AM
тАО02-26-2007 01:36 AM
Re: fetching data from server using SNMP trap in Open VMS 7.2
and check Geni's answer.
Wim
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-26-2007 01:53 AM
тАО02-26-2007 01:53 AM
Re: fetching data from server using SNMP trap in Open VMS 7.2
My procedure is ready and even if try to run this procedure, I am unable to recieve. The system halts with no response after giving command.
can this be a memory issue? or because of too much data it is trying to recieve?
If so what are the troubleshooting procedureon this?
Amit.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-26-2007 03:36 AM
тАО02-26-2007 03:36 AM
Re: fetching data from server using SNMP trap in Open VMS 7.2
Your reference to halt here is not to a system halt or system crash or a process-level failure, and just intended to indicate that the DCL procedure simply stops at the step where it is receiving the trap, correct? That the loop appears to hang at the trap receive, correct? ("Halt" generally implies a particular meaning on OpenVMS.)
Is there a trap arriving at the receiver? The lack of that arrival would be my initial guess here.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-26-2007 06:25 PM
тАО02-26-2007 06:25 PM
Re: fetching data from server using SNMP trap in Open VMS 7.2
No, the trap is not arriving at reciever. All the problem starts from there.
Thats why I used the word 'halt' in my mail, as there is no further progress seen or any error message from the system.
Amit.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-26-2007 07:22 PM
тАО02-26-2007 07:22 PM
Re: fetching data from server using SNMP trap in Open VMS 7.2
Can you ping the servers and can they ping you ?
Wim
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-26-2007 07:53 PM
тАО02-26-2007 07:53 PM
Re: fetching data from server using SNMP trap in Open VMS 7.2
I am trying to recieve the trap, using following command,
$ snmp_traprcv -d -p 1024,
After giving this command, the system don't give any response.
Amit.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-26-2007 07:57 PM
тАО02-26-2007 07:57 PM
Re: fetching data from server using SNMP trap in Open VMS 7.2
Wim
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-26-2007 08:05 PM
тАО02-26-2007 08:05 PM
Re: fetching data from server using SNMP trap in Open VMS 7.2
Attached is a procedure I wrote, specific to our company, but will give you an idea of how it works.
Rob.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-27-2007 06:16 PM
тАО02-27-2007 06:16 PM
Re: fetching data from server using SNMP trap in Open VMS 7.2
$ @TCPIP$SNMP_REQUEST.EXE
%RMS-W-RTB, 512 byte record too large for user's buffer
can you guessanything from this.
Amit.