- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: DL320 G5 Sata Raid problem
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Forums
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-21-2010 03:59 AM
01-21-2010 03:59 AM
DL320 G5 Sata Raid problem
I found 1 disk in failed state (with controller bios diagnostic, since leds are off). I powered down the server and changed the failed disk with a new one, and the status of the array changed to "FAILED".
Then I plugged the disks to another pc and I found that the "good" disk had ONLY the windows default folders, such as the raid1 worked only during the os installation.
How is it possible? I used the sata raid driver to install the os, loading it by pressing F6 at the prompt during the installation.
Any help is appreciated not to repeat the problem in the future
thanks in advance
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-21-2010 04:29 AM
01-21-2010 04:29 AM
Re: DL320 G5 Sata Raid problem
Smart Array + Drive backplane + drives.
Reseat disk or power cycle server would also bring it back on-line.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-21-2010 04:43 AM
01-21-2010 04:43 AM
Re: DL320 G5 Sata Raid problem
I updated all FW with firmwareCD 8.60 in december 2009
I think I missed to install some sw because the controller didn't write the data to both disks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-21-2010 04:46 AM
01-21-2010 04:46 AM
Re: DL320 G5 Sata Raid problem
But do check, if new fw is available.
Lot's of new fw has come since FW CD 8.60.
br
/jag
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-21-2010 01:19 PM
01-21-2010 01:19 PM
Re: DL320 G5 Sata Raid problem
disable raid in bios back up to a disk from tape
insert disk in windows add the raid driver in dev manager
now add a physical disk now reboot and in bios enable raid
now you have windows waiting with a raid driver all ready and the server is setup for raid now the disks will mirror.
enjoy :)
This is how we thank each other in the forum
http://forums11.itrc.hp.com/service/forums/helptips.do?#33
Enjoy:)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-22-2010 01:10 AM
01-22-2010 01:10 AM
Re: DL320 G5 Sata Raid problem
I can see the raid 1 array in the post, and Windows can see only 1 disk, and I had to put RAID drivers to install the os.
I want to know.. do I need other software in the operating system to have raid1 working?
On the 2nd disk there was only a fresh windows installation and it's really strande in my opinion
thanks in advance