- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Fuse on Intercon.Switch Blades
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-25-2005 09:05 PM
тАО09-25-2005 09:05 PM
Fuse on Intercon.Switch Blades
I replaced one of the 'Interconnects', but power is stil off. Checking though web access, clicking on Interconnect Switch I found that one of the fuses is down. Where are these fuses?! In the enclosure or inside the Interconn. switch?! What is troubleshooting procedure?! I did not find it in the Blade documents. Or, simply I missed something.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-27-2005 12:50 AM
тАО09-27-2005 12:50 AM
Re: Fuse on Intercon.Switch Blades
You may have a bad pwr backplane or signal backplane. YOu can also try swapping these with another enclosure to see which is not working.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-27-2005 05:26 PM
тАО09-27-2005 05:26 PM
Re: Fuse on Intercon.Switch Blades
Check page 13 for components ├в reset them
Did you get any light on the back?
http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00065042/c00065042.pdf
Can you see second enclosure trough management links - Power management Module Firmware at least 2.10 or 2.20? and reset after
Fuses is part of backplane on the enclosure, it's not a physical switch or etc ..
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-27-2005 08:08 PM
тАО09-27-2005 08:08 PM
Re: Fuse on Intercon.Switch Blades
I have 2 racks, 1-st one with 3 p-enclosures, and 2-nd with 2 p-enclosures. As the first rack installation is priority, I swapped that enclosure by good one to keep working on Blade servers.
FW for p-enclosure is 2.20
FW for power enclosure is 2.10
I will test this issue again on 2-nd rack.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-27-2005 08:35 PM
тАО09-27-2005 08:35 PM