installing HP Smart Array P440 on the DL180 Gen9

[Lampard33]

I need to upgrade the actual controller of my server (DL180 Gen9 with a 8 LFF drive cage) from a H240 to a HP Smart Array P440/4GB FBWC 12Gb 1-port Int SAS Cont. Server 778455-B21, System ROM, U20 v2.80 (10/16/2020). P440 allows you to create arrays in hp smart storage administrator, but it is not displayed in one-time boot menu. The bios settings were not changed after p240 was replaced with p440. 

[support_s]

System recommended content:

1. HPE Smart Array P440 Controller

2. HPE ProLiant DL180 Generation9 (Gen9)

If the above information is helpful, then please click on "Thumbs Up/Kudo" icon.

Thank you for being a HPE community member.

[Cali]

Did you see the Controller in BIOS/UEFI?

F9 > System Configutation > Slot x Smart Array
Video - HPE ProLiant Servers - Introduction to UEFI HPE System Utilities | HPE Support

There you configure your Volumes/Raid first.

Cali

[Lampard33]

bios/Platform Configuration:

https://disk.yandex.ru/i/MZ_oqf5McJ2rZg 

[Cali]

Perfect, move down to Slot 1 and configure the Raid & Volumes.

[Lampard33]

I configured Raid in the smart storage administrator utility, is this not correct?

[Cali]

It's the same.
So the Controller is visible and you configure successfully the Raid and Volume, but the OS did not find a Disk or the Controller during Setup?

[Lampard33]

The OS is installed normally, the disk is visible. But the OS doesn't load. The P440 controller is not in the UEFI Boot Order. Is setting the priority of bootable logical disks/volumes in smart storage administrator utility necessary?

[Cali]

OMG- That's strange
The last thing I know is BIOS (2.90_04-29-2021) and Array Firmware (7.0) up to Date?

Software Details - System ROM Flash Binary - HPE ProLiant DL160 Gen9/DL180 Gen9 (U20) Servers | HPE Support

Software Details - Online ROM Flash Component for Windows (x64) - Smart Array and Smart HBA H240ar, H240nr, H240, H241, H244br, P240nr, P244br, P246br, P440ar, P440, P441, P542D, P741m, P840, P840ar, and P841 | HPE Support

If yes, I'm out.

Cali

[Lampard33]

Bios v2.80 (10/16/2020)

Array Firmware (7.0)

Is setting the priority of bootable logical disks/volumes in smart storage administrator utility necessary?

[Cali]

As far, I know this setting for bootable devices is only needed for Legacy Boot Mode.

So Question is: Do you use Legacy Boot = BIOS or UEFI Boot?

The controller boots from the first logical drive by default.

Cali

The UEFI System Utilities is embedded in the system ROM. The UEFI System Utilities enable you to
perform a wide range of configuration activities, including:
• Selecting the primary boot controller

Setting bootable devices for Legacy Boot Mode
Setting the primary and secondary bootable devices (Legacy Boot Mode)
Procedure
1. From the System Utilities screen, select System Configuration > controller > Set Bootable
Device(s) for Legacy Boot Mode > Select Bootable Logical Drive > logical drive.
2. In the Logical Drive screen, select either of the following:
• Set as Primary Bootable Device
• Set as Secondary Bootable Device
Setting the number of OS bootable drives (Legacy Boot Mode)
Procedure
1. From the System Utilities screen, select System Configuration > controller > Set Bootable
Device(s) for Legacy Boot Mode > Number of OS bootable drives.
2. In the Number of OS bootable drives screen, specify the number of OS bootable drives.
3. Click Submit Changes.

[Lampard33]

I use UEFI

[Lampard33]

I found a similar case
but I do not know how to clear the controller configuration?