- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Server Management - Remote Server Management
- >
- Cannot change nic for PXE
Server Management - Remote Server Management
1752610
Members
3989
Online
108788
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-18-2005 07:46 AM
тАО01-18-2005 07:46 AM
I inadvertently disabled NIC 1 for PXE. At the same time, I believe I set the password for Administartor. I now am unable to re-enable the NIC. I reboot the server, press pf10 as requested. It prompts me for a password. I put in the password that I reset, but it says the password is not correct. It then only allows me read access. I did try changing the dip switch for ILO security. When the sever reboots, it warns me security is disabled. However, when I go into the utility, it still prompts me for a password. Any assistance would be appreciated.
Solved! Go to Solution.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-18-2005 03:39 PM
тАО01-18-2005 03:39 PM
Solution
You need to set a different dip switch.
Look for the system maintenance switch, position 5. This is labeled "password" or "power on password" or something similar. Consult the hood label for specifics on your system.
This allows you to enter host RBSU without password. There you can reconfigure the password.
The iLO security override switch disables security to the iLO subsystem and to iLO RBSU. However, this is deliberately different than access to the host RBSU.
Look for the system maintenance switch, position 5. This is labeled "password" or "power on password" or something similar. Consult the hood label for specifics on your system.
This allows you to enter host RBSU without password. There you can reconfigure the password.
The iLO security override switch disables security to the iLO subsystem and to iLO RBSU. However, this is deliberately different than access to the host RBSU.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-19-2005 12:46 AM
тАО01-19-2005 12:46 AM
Re: Cannot change nic for PXE
Yes, that fixed my problem. Thanks!
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP