- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Server Management - Remote Server Management
- >
- Re: LO100 not responding
Server Management - Remote Server Management
1753499
Members
4463
Online
108794
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-14-2009 03:15 AM
03-14-2009 03:15 AM
LO100 not responding
Have several dl140G3 and dl160G5 with the latest bios and ilo-firmware.
I use a script that polls the temperature reported on the sensors-page. The poll runs every 5 mins. This used to work fine, but after I upgraded to the latest firmware the iLO stops responding after about 24h. When in this state iLO will not respond to http or telnet.
Only way to get it back up and running is by removing the power, wait 30 sec and hook it up again.
Any way to get around this? Is there a limit on how many polls you can run pr hour?
The best would be if iLO-port could do SNMP and I could poll that instead of http :)
I hope some of you have a good solution for this problem so I don't have to stop polling for temps.
I use a script that polls the temperature reported on the sensors-page. The poll runs every 5 mins. This used to work fine, but after I upgraded to the latest firmware the iLO stops responding after about 24h. When in this state iLO will not respond to http or telnet.
Only way to get it back up and running is by removing the power, wait 30 sec and hook it up again.
Any way to get around this? Is there a limit on how many polls you can run pr hour?
The best would be if iLO-port could do SNMP and I could poll that instead of http :)
I hope some of you have a good solution for this problem so I don't have to stop polling for temps.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-04-2009 06:15 AM
06-04-2009 06:15 AM
Re: LO100 not responding
Having very similar problem, see
http://forums13.itrc.hp.com/service/forums/questionanswer.do?threadId=1340820
Please do a post here if you get any more info about this problem.
http://forums13.itrc.hp.com/service/forums/questionanswer.do?threadId=1340820
Please do a post here if you get any more info about this problem.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP