HP SIM 5, SP5 and ILO

[Tommy Frandsen_1]

Hello

I have trouble with discovering our 380G4 servers ILO boards. We have set the SNMP settinga in the ILO to point to the SIM servers IP and all settings enabled.
But still when we try to add the ILO to our SIM we are not able to. I have treid to read through documentation from HP, with no luck.
We are running FW1.84 on the ILO.
What can we do to add our ILO's in the SIM.

Thank you in advance.
Tommy

[Ted Rodavich]

This may sounds silly, but you DO have a network cable plugged into it and you CAN ping it?

[sandeep_raman]

Hello Tommy,

Check if this is of help,

http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=542332

SRH

[Tommy Frandsen_1]

Hi and thanks for your replys.

First of all: yes we have the cables plugged in and we can ping and also log on to administer/use the iLO.

I checked the link you send and it did not clear things for me.
In the v1.84 firmware you can not set the option: SNMP/Insight Manager --> HIGH

In the administration tab--> SNMP/Insight Manager we have enabled the following:
SNMP Alert Destinations:
-iLO SNMP alerts
-forward Insight Manager Agents SNMP alerts
-SNMP pass-thru
SNMP alert destination is set to the IP of our SIM5 server and we can send a test trap to the SIM server.
In Configure Insight Manager Integration we have set the iLO to point the "host" servers DNS name.

As i see it thit should be enough for the SIM to be able to discover but it can't.

Does this make sense?

Best Regards
Tommy

[T. Vander Auwera]

When you ping and log into the iLO, do you try that from a workstation on the network or from the HPSIM server console itself?

[sandeep_raman]

Hello Tommy,

It seems perfect,strange it still does'nt discover Ilo.
Have you tried a manual discovery using the Ilo Ip?

SRH

[Rob Buxton]

The older ILO F/W had a section where you specified the level of data returned, that needed to be set to at least Medium for the ILO / Server match ups to work.
Later F/W versions just seem to have Data return Enabled or Disabled. You'll want that enabled.

I just ensure the ILOs and Servers are in the Discovery Ranges. You could try a manual discovery on the appropriate IP Address.

The other thing to check is that you do not have Discovery Filters enabled, or if you do that you're not excluding management processors.

[Tommy Frandsen_1]

Hi all

We seem to have found the problem. We can ping the iLO's from every workstation we have on the network and also from some of the servers, but we found out that we could NOT ping from the management server itself. But from the management server we CAN ping RILOS and older versions of management processors.
We have now asked the network department to check up on the swithches as it seems to be one of then who has a faulty arp table.

But thank you very much for your help anyway.

BR
Tommy

[Dmitri Manushin]

Hello, i have the sametrouble, i can ping iLO interface from any pc in network but can't from SIM server, SIM and iLo located in one subnet, also i'm found that other servers located in different subnet is pinged from SIM and i can add iLO. why???

HP SIM version 5 SP5 iLO version is 1.80 and as Tom sad we too can open iLO trough web but not from SIM server

[Dmitri Manushin]

I'm resolve my problem. First what i'm complete it SNMP Alert Destination, then i'm enable SNMP Alerts and other 2 parameters, then i'm enter ip address of SIM server to Insight manager Web Agent URL , apply settings and setart iLO card. Now i can ping it from SIM server and add to SIM. :)

[Dmitri Manushin]

:( all iLO now is down, i'm mean not accessable from SIM server, i'm found that it work fine about 5 minutes and then down for SIM, if i restart iLO card it will work for SIM 5 minutes and down. any idea???


thank you.

[Dmitri Manushin]

I'm switch Team settings from Automatic to Network Fault tolerance Only (NFT) in SIM server and now everything is work. We have HP DL360G4p with 2 HP NC7782 Gigabit Adapters connected to Cisco Catalyst 3750G-24TS-S1RU.