- Community Home
- >
- Networking
- >
- Software Defined Networking
- >
- Openflow command is not working in 2920-24G J9726A
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-13-2013 01:47 AM - last edited on 11-17-2013 06:38 PM by Lisa198503
11-13-2013 01:47 AM - last edited on 11-17-2013 06:38 PM by Lisa198503
Openflow command is not working in 2920-24G J9726A
I want to set up SDN set up , i have two hp switches ( 2920-24G J9726A), and controller. By serial port terminal i can access the console of the switch . In hp switch the command openflow is not working . I have tried enabling openflow but CLI is not detecting openflow command and giving error that it is invalid input .
HP-2929-24G(config)# openflow
HP-2929-24G(config)# show openflow
invalid input : openflow
Please if any one can guide me how to enable openflow command and also steps to link both the switches through trunk .
Thanks
P.S. This thread has been moved from ProCurve / ProVision-Based to SDN Discussions. -HP Forum Moderator
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-14-2013 11:11 PM
11-14-2013 11:11 PM
Re: Openflow command is not working in 2920-24G J9726A
Whats your firmware? - As per the release notes seems its part of WB.15.12.0010 available on the portal..
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-20-2013 03:51 AM
11-20-2013 03:51 AM
Re: Openflow command is not working in 2920-24G J9726A
adding to previous post.....from HP's Openflow Admin Guide I can see that the support for 2920 series was added in the following firmware versions
K/KA.15.12 and WB .15.12
and you can find detailed steps to carry out the configuration as well in the same guide...
Ref: http://h20628.www2.hp.com/km-ext/kmcsdirect/emr_na-c03991489-1.pdf
HTH..
-J
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-21-2013 10:57 AM
11-21-2013 10:57 AM
Re: Openflow command is not working in 2920-24G J9726A
WB.15.12 has support for OpenFlow 1.0
WB 15.14 has support for OpenFlow 1.3
You can download software for the 2920 here: https://h10145.www1.hp.com/downloads/SoftwareReleases.aspx?ProductNumber=J9836A