- Community Home
- >
- Networking
- >
- Legacy
- >
- Switching and Routing
- >
- LACP no create a dyn1 group
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-18-2021 06:58 AM - last edited on 09-08-2021 10:37 AM by support_s
08-18-2021 06:58 AM - last edited on 09-08-2021 10:37 AM by support_s
LACP no create a dyn1 group
Switch# configure terminal
Switch(config)# interface 1-4
Switch(eth-1-4)# lacp active
Switch(eth-1-4)# show lacp
PORT LACP TRUNK PORT LACP LACP
NUMB ENABLED GROUP STATUS PARTNER STATUS
---- ------- ------- ------- ------- -------
1 Active 1 Down No Success
2 Active 2 Down No Success
3 Active 3 Down No Success
4 Active 4 Down No Success
Why he create a 4 groups ? anyone can help me?
i need cread a dyn1 group
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-18-2021 07:15 AM
08-18-2021 07:15 AM
Re: LACP no create a dyn1 group
You have to bind these ports into a trunk (trk1).
Please refer below link:
https://support.hpe.com/hpesc/public/docDisplay?docLocale=en_US&docId=emr_na-c02456299
Thanks!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-18-2021 11:26 AM - edited 08-18-2021 11:56 AM
08-18-2021 11:26 AM - edited 08-18-2021 11:56 AM
Re: LACP no create a dyn1 group
Hello,
What you are trying the configure is called dynamic trunk group. You are enabling lacp active on interfaces 1 to 4. However in order for the dynamic trunk to be formed, the ports have to be up and the device on the other side on this ports has to be configured with LACP active or passive, so when they receive LACP BPDUs from the local switch they can respond. The local switch will only create a dyn1 trunk interface when it receives LACP responses from the device on the other side which indicate the same LACP system ID.
From the output it looks like the ports are down and there is no LACP partner. In this case the switch cannot aggregate the ports to a dyn interface and they are kept separate. You have to connect all 4 ports to another switch and the ports of the other switch have to be configured as LACP passive or LACP active. Both switches have to exchange LACP BPDU and based on that verify that all 4 ports are connected to the same partner. Only after that will the dynamic trunk interface dyn1 be formed.
Keep in mind that this configuration option is not used very often. I personally dont remember any customer using it. It has also some restrictions compared to the trunk option. For example you cannot configure tagged VLANs on it. It is better to use the static LACP trunk using the trunk command, here an example
switch(config)# trunk 1-4 trk1 lacp
With this command interface trk1 is created immediately even if the ports are down. However when the ports go online LACP is doing again a BPDU exchange and if it cannot be verified that the ports connect to the same device on the other side, the ports will be blocked. So you still have the advantage of LACP.