MSA500 on RHEL5 and DL380G6

[Fadia Almarei]

Dear All

i have RHEL5 os installed on EL380 G6 server , i connect MSA500 G2 storage to the server , i see the scsi devices but i do not see the hard disks on it , what should i do , and how could i see them.
[root@SReplica host0]# more /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: TEAC Model: DV-W28S-RS Rev: G.C4
Type: CD-ROM ANSI SCSI revision: 05
Host: scsi2 Channel: 00 Id: 00 Lun: 00
Vendor: COMPAQ Model: SMART ARRAY CL Rev: 1.90
Type: RAID ANSI SCSI revision: ffffffff
Host: scsi2 Channel: 00 Id: 01 Lun: 00
Vendor: COMPAQ Model: SMART ARRAY CL Rev: 1.90
Type: RAID ANSI SCSI revision: ffffffff

[Ivan Ferreira]

Install the array configuration utility and verify if you can see the disks using this tool.

Sometimes, a reboot is needed to detect disks if a rescan of the scsi bus does not do the job.

[palaniappan.sp]

Hi Fadia,

what fdisk -l shows? and did you installed SCSI adapter and its driver?

Regds
Palani

[Fadia Almarei]

we install it and it show nothing rather than local disks, and we did reboot,
[root@SReplica ~]# fdisk -l

Disk /dev/cciss/c0d0: 293.5 GB, 293563949056 bytes
255 heads, 63 sectors/track, 35690 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

Device Boot Start End Blocks Id System
/dev/cciss/c0d0p1 * 1 76 610438+ 83 Linux
/dev/cciss/c0d0p2 77 35690 286069455 8e Linux LVM

[Ivan Ferreira]

Please run hpacucli and execute the following command:

=> ctrl all show config detail


Post the results.

[Fadia Almarei]

=> ctrl all show config detail

Smart Array P410i in Slot 0 (Embedded)
Bus Interface: PCI
Slot: 0
Serial Number: 50123456789ABCDE
Cache Serial Number: PAAVP9SXQAFY
RAID 6 (ADG) Status: Disabled
Controller Status: OK
Chassis Slot:
Hardware Revision: Rev C
Firmware Version: 1.62
Rebuild Priority: Medium
Expand Priority: Medium
Surface Scan Delay: 15 secs
Queue Depth: Automatic
Monitor and Performance Delay: 60 min
Elevator Sort: Enabled
Degraded Performance Optimization: Disabled
Inconsistency Repair Policy: Disabled
Post Prompt Timeout: 0 secs
Cache Board Present: True
Cache Status: OK
Accelerator Ratio: 25% Read / 75% Write
Drive Write Cache: Disabled
Total Cache Size: 512 MB
No-Battery Write Cache: Disabled
Cache Backup Power Source: Batteries
Battery/Capacitor Count: 1
Battery/Capacitor Status: OK
SATA NCQ Supported: True

Array: A
Interface Type: SAS
Unused Space: 0 MB
Status: OK



Logical Drive: 1
Size: 273.4 GB
Fault Tolerance: RAID 5
Heads: 255
Sectors Per Track: 32
Cylinders: 65535
Stripe Size: 64 KB
Status: OK
Array Accelerator: Enabled
Parity Initialization Status: Initialization Completed
Unique Identifier: 600508B1001037383941424344450400
Disk Name: /dev/cciss/c0d0
Mount Points: /boot 596 MB
Logical Drive Label: A013C1D750123456789ABCDEFD0F

physicaldrive 1I:1:1
Port: 1I
Box: 1
Bay: 1
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 15000
Firmware Revision: HPDC
Serial Number: 3TB0DVMG00009006ZCTB
Model: HP DH0146FAQRE
PHY Count: 2
PHY Transfer Rate: 6.0GBPS, Unknown
physicaldrive 1I:1:2
Port: 1I
Box: 1
Bay: 2
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 15000
Firmware Revision: HPDC
Serial Number: 3TB0DS8T00009007JFJP
Model: HP DH0146FAQRE
PHY Count: 2
PHY Transfer Rate: 6.0GBPS, Unknown
physicaldrive 1I:1:3
Port: 1I
Box: 1
Bay: 3
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 146 GB
Rotational Speed: 15000
Firmware Revision: HPDC
Serial Number: 3TB0DRM700009007DNQE
Model: HP DH0146FAQRE
PHY Count: 2
PHY Transfer Rate: 6.0GBPS, Unknown

[Ivan Ferreira]

It seems that the system is detecting only the internal controller with 3 disks. And the device that you currently see in the fdisk -l output is an array of the internal controller.

You should check your hardware connections.

[Fadia Almarei]

we will check it again and try