About vishnu.khandare

vishnu.khandare · ‎02-15-2013

Taking Ignite of same server on same server will be useless. That cant be used is system gets crashed. Regards Vishnu Khandare

vishnu.khandare · ‎02-15-2013

Hi, As posted earlier also by others there are two options to take Ignite one is on tape and other is on Network that will land on Ignite server. By Ignite u can take backup of vg00 which can be restored in case ur OS got crashed. U cannot take Ignite of one server on same server, as its creates the copy of VG00. U need to connect tape drive to same server or in network then only u can take Ignite of the server. Hope this clear ur query. Vishnu Khandare

vishnu.khandare · ‎05-16-2012

Hi Chandu, Which cluster u hav configured, legacy or modular. If modular cluster, in cluster config file we have to define the subnet, It will monitor perticular physical IP in that subnet, it will not monitor whole subnet. Ur next point is if L3 switch goes down, then definalty whole subnet connected to it wil get down. hope ur queries resolved. Regards Vishnu

vishnu.khandare · ‎05-16-2012

Hi, Make user u hav disable the oracle integration. Else application and DB can run as it in single node. If u want u can do cmdeleteconf to delete all cluster configuration. Vishnu

vishnu.khandare · ‎05-16-2012

Hi, Please check the dmseg, check the drive is On, check drive is proparly connected to scsi. Regards Vishnu

vishnu.khandare · ‎05-16-2012

use correct path thats sbin instead of bin, Problem resolved.

vishnu.khandare · ‎04-13-2012

This output means, tape is there in this drive. Rewind it if u want to check whether tape is jam or not. Rewind can be done from command only check man page of mt for more infor. Hope this resolves. Regards Vishnu Khandare

vishnu.khandare · ‎04-13-2012

Hi One solution is there if u have the network ignite server in place and have the image of other BL870i2 server u can push it and install server. And if u want to take ignite of Bl870i2 that also can be taken if u have the tape library from tht a drive is mapped on to this server by using that drive u can take network ignite on tape. Hope it is clear. Regards Vishnu

vishnu.khandare · ‎04-13-2012

Hi, Is ignite installed, check by, #swlist | grep -i ignite If found installed, run #whereis make_tape_recovery and take full path and run the cmd to take ignite. Regards Vishnu

vishnu.khandare · ‎04-13-2012

Hi Friends, I m facing n issues while implementing the RBAC, pls find belwo error. $ privrun /usr/sbin/useradd new_user privrun: authorization check failed Is there any permission issue, do we need to provide the rbac dir. Pls help to resolve Regards Vishnu

vishnu.khandare · ‎04-13-2012

Hi, Is there any issue with FC Cable connectivity, that might make the SAN unavalailiblity. Pls share #isocan -fnC disk Regards Vishnu

vishnu.khandare · ‎07-15-2011

Hi Ur first point is correct... to take ignite asign the DAT drive to IVM and take Ignite. Second one... to restore u must add the drive..b4 start then normal process of restore. Hope this resolves ur query.. Regards Vishnu Khandare

vishnu.khandare · ‎06-10-2011

Hi Rajesh, Yes, its very correct u can create N no of user in single command. But its best practice is to create user one by one, so that if u want to give different parameters u can provide. like shell ,group etc. Hope ur query resolved. Regards Vishnu Khandare

vishnu.khandare · ‎06-07-2011

Hi Minhaz, Its correct procedure to follow for HyperThreading.You can go ahead. Hope this solves ur query. Regards Vishnu Khandare

vishnu.khandare · ‎06-07-2011

Hi Nirukshitha, from the swlist u will get all the softwares installed on the OS. And from ioscan -fn will list u all the hardware installed. By using ioscan with other parameters u can get more details of each means cpu, disk etc. Hope this solves ur query. Regards Vishnu Khandare

vishnu.khandare · ‎06-07-2011

Hi Vidhya B, for ur query i guess u want to write a script to get the said parmeters. R u ware of the command "logins -aox" Please check its man page even this command give the output of all the users with, last passwd reset, PASSWORD_MAXDAYS PASSWORD_MINDAYS PASSWORD_WARNDAYS and many more check its man page for more details. Hope this solves ur query. Thanks & Regards Vishnu Khandare

vishnu.khandare · ‎04-13-2011

Hi, Make sure you have to add san disk/LUN to host and run hpvmmodify from host only. check with hpvmdevmgmt -l all | grep -i diskXX perticular disk which ur going to add in that IVM,which VM is holding tht disk. If the IVM version is lower then 4 then it will not add the disk online it requiers reboot of guest IVM to reflect the disk. Second thing is once u get the disk in guest IVM do pvcreate and vgextend. If possible reboot the guest and check disk status. Hope this resolves. Regards Vishnu Khandare

vishnu.khandare · ‎04-13-2011

Hi, As per ur problem desciption, you want to extend the mountpoint/Logical Volume in the Guest IVM. U have the storage LUN at host IVM, u need to added the LUN/Disk to required guest, by hpvmmodify, then check in Guest IVM. After getting the disk/LUN extend the required logical volume or mount point. Hope this help to resolve ur problem Regards Vishnu Khandare

vishnu.khandare · ‎02-16-2011

Hi Jona, Command for the network ignite with excluding /tmp will be for network ignite use below cmd #/opt/ignite/bin/make_net_recovery -s ignitdev -a ignitdev:/ignite_image/hostname -x inc_entire=vg00 -x exclude=/tmp Please refer below thread for more help, http://h30499.www3.hp.com/t5/Ignite-UX/configure-ignite-for-itanium-HPUX/m-p/4698194#M17664 Hope this resolves ur query. Regards Vishnu Khandare

vishnu.khandare · ‎02-16-2011

Hi Ani, >>>to add a new client to my ignite server In the ignite server 1./opt/ignite/bin/add_new_client -s < Ignite server name> -f 2 . Make sure the permission of the below directories are 755 and ownership is bin:bin /var/opt/ignite/clients /var/opt/ignite/recovery/archeives/apps1 3 . make sure that you /etc/exports file is having the below entires /var/opt/ignite/clients -anon=2 /var/opt/ignite/recovery/archives/ -anon=2 ,access= 4. perfrom #exportfs -a On client server check #showmount -a command to confirm whether the filesystem is properly exported Run the command from clieant and take ignite. Refer link http://h30499.www3.hp.com/t5/Ignite-UX/configure-ignite-for-itanium-HPUX/m-p/4698194#M17664 Hope this solves ur query. Don't forget to assign points. Regards Vishnu Khandare

vishnu.khandare · ‎01-29-2011

Hi, Please check the /var/adm/syslog/syslog.log for recent changes regarding this tape drive, and run ioscan -fnC tape Regards Vishnu Khandare

vishnu.khandare · ‎01-29-2011

Hi, first U check is that Tape Drive power ON or not. If no, ON it, run ioscan -fnC tape. Have U replaced this tape drive with previous one? even then its showing NO_HW? In this case scsi id need to replace u need to run one command with the scsi id u will get in /var/adm/syslog/syslog.log form recent logs. Run this command #scsimgr -v -f replace_wwid -C lunpath -I XX please give scsi id in place of XX Hope this solves ur issue, by doing this no need to take reboot. Regards Vishnu Khandare

vishnu.khandare · ‎01-21-2011

Hi Jean >>>>>And another question when I try to install it using swinstall -s >>>>I am not getting anything in the swinstall window. No depot to chose! U can install from the downloaded package as well, Can u please share what exact error ur getting. Regards Vishnu Khandare

vishnu.khandare · ‎01-17-2011

Hi Deepak, As you said the problem is high i/o, Which process are on top, check its priorites U need to check what the big files then try to perf that files. tak backup/ reomve. Its gud to hav this system dir on VG00 root disk. Dont move it on SAN. Its better to move data mount points on SAN from root VG. Regards Vishnu Khandare

vishnu.khandare · ‎01-16-2011

Hi Sree, U have PV:/dev/dsk/c3t2d0 PV:/dev/dsk/c5t0d2 To create a VG fro this two PV, run belo commands, #pvcreate -f /dev/rdsk/c3t2d0 #pvcreate -f /dev/rdsk/c5t0d2 #mkdir /dev/vg0X ; X u can give any no #mknod /dev/vg0X/group c 64 0x0X0000 #vgcreate -p 60 -s PE_size -e 12500 /dev/vg0X /dev/dsk/c3t2d0 /dev/dsk/c5t0d2 Now this will create a VG vg0X U can create logival volume under it as per ur req. Hope this solves ur query. Regards Vishnu Khandare

Re: How to take ignite backup

Re: How to take ignite backup

Re: What is subnet monitoring in HP service guard.

Re: hpux cluster mode to non cluster mode

Re: "ioscan -fnNC tape" shows devices with "NO_HW"

Re: RBAC Implementaion

Re: mt status output

Re: HP i870 Integrity Blade

Re: How to install the make_tape_recovery in our H...

RBAC Implementaion

Re: bdf,df,umount get hangs

Re: Ignite Backup and Restore on Virtual Machine

Re: useradd command

Re: Enable HyperThreading in HP-UX V3

Re: how to find the HW inventory of rx server

Re: Need to get password Attributes

Re: Extending a LUN used by an iVM whilst online

Re: Extending a LUN used by an iVM whilst online

Re: ignite

Re: adding a new client to ignite

Re: Tape drive showing no hardware

Re: Tape drive showing no hardware

Re: Bind Installation from DVD

Re: Suggestions on moving folders from internal di...

Re: creation of PVG based VG