- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: Command View EVA (6, 6.02 and 7) Service start...
Disk Enclosures
1756288
Members
2608
Online
108844
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-11-2007 02:31 AM
тАО10-11-2007 02:31 AM
Hello,
on all 3 Versions (6, 6.02 and 7) of Command View EVA (EVA4000, XCS 6.100) the service could not start: It stays on "starting", and stop, start and restart are greyed out. Only the properties to manual or disabled for next restart can be changed.
Before, the Microsoft-Hotfixes where installed, but after "deinstalling" them (by using the System-Image-before), same problem. So I would say "no changes occur"!
Any ideas?
Thanks and regards
Rudolf
on all 3 Versions (6, 6.02 and 7) of Command View EVA (EVA4000, XCS 6.100) the service could not start: It stays on "starting", and stop, start and restart are greyed out. Only the properties to manual or disabled for next restart can be changed.
Before, the Microsoft-Hotfixes where installed, but after "deinstalling" them (by using the System-Image-before), same problem. So I would say "no changes occur"!
Any ideas?
Thanks and regards
Rudolf
Solved! Go to Solution.
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-17-2007 12:19 PM
тАО10-17-2007 12:19 PM
Re: Command View EVA (6, 6.02 and 7) Service start times out
I am having the same issues after installing the latest batch of hotfixes. I am keen to hear if there is a solution to this.
Peter.
Peter.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-17-2007 02:06 PM
тАО10-17-2007 02:06 PM
Solution
I ended up trying everything
- un-installed hotfixes
- re-image management server to previous hotfix install
- replaced hba
- replaced fibre cable
The solution in the end was to power cycle the 2 controllers, this was the only thing I could do to get the command view eva service to start. (not the ideal solution but I am lucky enough the system isn't live yet)
I am running command view 7.0 for EVA 4000 HSV200 version 6110
Peter
- un-installed hotfixes
- re-image management server to previous hotfix install
- replaced hba
- replaced fibre cable
The solution in the end was to power cycle the 2 controllers, this was the only thing I could do to get the command view eva service to start. (not the ideal solution but I am lucky enough the system isn't live yet)
I am running command view 7.0 for EVA 4000 HSV200 version 6110
Peter
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-17-2007 11:13 PM
тАО10-17-2007 11:13 PM
Re: Command View EVA (6, 6.02 and 7) Service start times out
Thank you Peter,
I have disbaled the FC-Ports on the node, and the service is starting, but CV has no accesss to the EVA. Then I have rebooted the Master-Controller due to an outstanding operation -> this solves the issue.
So your tip, rebooting the Controllers would also fixed the problem!
Regards
Rudolf
I have disbaled the FC-Ports on the node, and the service is starting, but CV has no accesss to the EVA. Then I have rebooted the Master-Controller due to an outstanding operation -> this solves the issue.
So your tip, rebooting the Controllers would also fixed the problem!
Regards
Rudolf
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP