- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: HP L class server not able to take a console
HPE 9000 and HPE e3000 Servers
1756301
Members
2506
Online
108844
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-09-2011 06:03 AM
тАО01-09-2011 06:03 AM
HP L class server not able to take a console
Hi ,
This is Veera , We have HP L Class(2000) server for R&D purpose,we do not have IP details for the servers so i am trying to take console using DB25-DB9 cable on GSP Port but could not able to take a console using hyper terminal tool on windows client.The LED Status is Run:Green-Glowing ,Attn: Amber - Glowing Fault: RED-Glowing,guys any solutions....?
This is Veera , We have HP L Class(2000) server for R&D purpose,we do not have IP details for the servers so i am trying to take console using DB25-DB9 cable on GSP Port but could not able to take a console using hyper terminal tool on windows client.The LED Status is Run:Green-Glowing ,Attn: Amber - Glowing Fault: RED-Glowing,guys any solutions....?
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-10-2011 01:31 PM
тАО01-10-2011 01:31 PM
Re: HP L class server not able to take a console
The L Class has a DB25 port, but actually uses an adapter cable to adapt to 3 DB9 cables (console, UPS, and remote(modem)). This may be required to get a solid console connection.
However, I have been successful in connecting with out this adapter. Be sure your cable is null-modem.
Lastly, try resetting the GSP. Open the side cover and push the reset button found on the board.
-Bob
However, I have been successful in connecting with out this adapter. Be sure your cable is null-modem.
Lastly, try resetting the GSP. Open the side cover and push the reset button found on the board.
-Bob
----------------
Was this helpful? Like this post by giving me a thumbs up below!
Was this helpful? Like this post by giving me a thumbs up below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-10-2011 02:09 PM
тАО01-10-2011 02:09 PM
Re: HP L class server not able to take a console
The LEDs of that L2000 system are indicating a hardware fault condition. A red Fault led + anything else = bad news.
The amber Attn LED should only be off or blinking, never continuously glowing.
If the server's been moved recently, my first recommendation would be to disconnect all power cables, then look inside and verify that all cards and other pluggable internal components are fully seated.
When connecting power to the server or resetting the GSP, you should see one or two LEDs light up in the rear panel next to the console connector, in the 2nd card slot from the bottom. If they stay red, the GSP has failed its self-test.
If they are red for a short while but then turn green, the GSP is resetting itself and might be working. In that case, try sending a Control-B keystroke through the Hyperterminal: the GSP should always answer to Control-B even if the OS or the rest of the server is down.
MK
The amber Attn LED should only be off or blinking, never continuously glowing.
If the server's been moved recently, my first recommendation would be to disconnect all power cables, then look inside and verify that all cards and other pluggable internal components are fully seated.
When connecting power to the server or resetting the GSP, you should see one or two LEDs light up in the rear panel next to the console connector, in the 2nd card slot from the bottom. If they stay red, the GSP has failed its self-test.
If they are red for a short while but then turn green, the GSP is resetting itself and might be working. In that case, try sending a Control-B keystroke through the Hyperterminal: the GSP should always answer to Control-B even if the OS or the rest of the server is down.
MK
MK
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-12-2011 10:44 AM
тАО01-12-2011 10:44 AM
Re: HP L class server not able to take a console
Hi Baskar,
Please connect the W cable (UPS,Remote and console)25pin end to System use 9Pin Console end to the Serial terminal or hyper terminal in windows.
LED status:
Run:Green
Attn: Amber
Fault: RED
The system is critical fault- Booting is not proceeded or Boot is pending.
Please login to Local console and CTRL+B will l give access to GSP to see the error.
HTH
Surendar
Please connect the W cable (UPS,Remote and console)25pin end to System use 9Pin Console end to the Serial terminal or hyper terminal in windows.
LED status:
Run:Green
Attn: Amber
Fault: RED
The system is critical fault- Booting is not proceeded or Boot is pending.
Please login to Local console and CTRL+B will l give access to GSP to see the error.
HTH
Surendar
I work for HPE
[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]
[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP