- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Aruba & ProVision-based
- >
- Re: Cannot Ping Subnets on HP Procurve 2510/v1910
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-10-2011 04:03 PM - last edited on тАО03-17-2014 02:36 AM by Maiko-I
тАО12-10-2011 04:03 PM - last edited on тАО03-17-2014 02:36 AM by Maiko-I
Cannot Ping Subnets on HP Procurve 2510/v1910
We are trying to setup three new switches and are having some difficulties when it comes to our overall WAN setup.
The switches function fine for the branch they are setup for but when trying to access or even ping the switches over the WAN from a different subnet we get no response.
The Procurve 2510 does not seem to have any routing capabilities so that's the one I'm most concerened about. Is there a setting or something I'm missing that would enable other subnets on the network to simply ping the switch? When it comes to the v1910s, I think I have that fixed by creaing a static route for 0.0.0.0 to the Default Gateway in that branch, would that be correct?
Can anyone offer some insight?
P.S. This thread has been moevd from Switches, Hubs, Modems (Legacy ITRC forum) to ProCurve / ProVision-Based. - Hp Forum Moderator
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-11-2011 07:17 PM
тАО12-11-2011 07:17 PM
Re: Cannot Ping Subnets on HP Procurve 2510/v1910
The 2510 switches do not do layer 3 routing, however if all you are trying to access is the management IP address of the switch then just make sure that the default gateway on the switch is set to the sites local router IP address (same as if it were a PC or server).
You can do this either via the web interface or via the CLI
config
ip default-gateway xx.xx.xx.xx
write memory
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-04-2013 01:51 AM - edited тАО07-04-2013 01:52 AM
тАО07-04-2013 01:51 AM - edited тАО07-04-2013 01:52 AM
Re: Cannot Ping Subnets on HP Procurve 2510/v1910
Hi - my situation - I am sitting on 192.168.1.0/24
2 HP 2910 Al4G switches sitting on 192.168.3.0/24
HP Switch 1 Default VLAN1 IP:
192.168.3.3
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.3.3
HP Switch 2 Default VLAN1 IP:
192.168.3.4
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.3.3
I can access any other device on the 192.168.3.x network using its access protocol (HTTP, PING, SNMP, Telnet) from the 192.168.1.x network.
I cannot access the management console of my switches via HTTP or Telnet from the 192.168.1.x network.
The only way I can access the switches is from a device/host located on the 192.168.3.x network using either HTTP or Telnet to either switches IP address.
Can anyone explain why? Thanks in advance
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-17-2014 12:33 AM
тАО03-17-2014 12:33 AM
Re: Cannot Ping Subnets on HP Procurve 2510/v1910
Hi did you ever manage to find out what the solution was to access the other switch network over the WAN?