StoreEver Tape Storage
1820390 Members
3445 Online
109623 Solutions
New Discussion

MSL 6030 and Network Storage Router e1200-160

 
Azamat
Frequent Advisor

MSL 6030 and Network Storage Router e1200-160

hi, all
I`ve some problem with msl6030… on this library customer has one drive, router (p/n 320101-001) , controller (p/n 231671-001)

Problem was that, msl don`t see drive, I replaced the router, but it didn`t see the any connections by scsi, and when i tried press discovery, router didn`t answered me(no ping, no reactions, i needed reboot the msl or router for working with this router)… so then I replaced the controller

I upgraded the firmware on the controller… but the router didn`t see any scsi connections

Then connected by next scheme: drive -> router -> controller, and I put terminator on the drive.

And yep, it`s working, router see the drive and controller, hp-ux don`t see this msl…
I didn`t find any documentations about the configuration the controller, only replacement the controller

I so stupid, that cann`t close this subcase the 3rd day!!!!

Thank for any advise (but not like “put your hands in your pockets, and do one step away” or “ just say that: i cann`t do this work, that mission impossible for me”

12 REPLIES 12
IBaltay
Honored Contributor

Re: MSL 6030 and Network Storage Router e1200-160

Hi,
maybe you could check the FC to SCSI drive mapping and if needed edit the port 0 map according to your needs - ( e.g. assign the HP-UX port wwns to the drives)
the pain is one part of the reality
Azamat
Frequent Advisor

Re: MSL 6030 and Network Storage Router e1200-160

ok, how i can do it, could you give me a link on the documentations, please, because i didn`t find any documentations for configuration.
Torsten.
Acclaimed Contributor

Re: MSL 6030 and Network Storage Router e1200-160

I don't know how it was before, but the SCSI connection should be

NSR -> lib ctrl -> drive -> terminator

Now do the mapping on the NSR - should be "indexed".

If you use zoning in your SAN (you should!) - check this too.

If you are now on hp-ux, inspect the "ioscan -fn" output for any UNKNOWN devices - maybe you need to install the "stape" and "schgr" drivers.


Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
IBaltay
Honored Contributor

Re: MSL 6030 and Network Storage Router e1200-160

Hi,
for mapping you can have a look in the user guide:
http://bizsupport.austin.hp.com/bc/docs/support/SupportManual/lpg29075/lpg29075.pdf

the pain is one part of the reality
Azamat
Frequent Advisor

Re: MSL 6030 and Network Storage Router e1200-160

2 Torsten.
yeah... i did by this schem: NSR -> lib ctrl -> drive -> terminator
2 IBaltay thx
Azamat
Frequent Advisor

Re: MSL 6030 and Network Storage Router e1200-160

can someone advice to me...
switch doesn`t have any zone configuration (no zoning)... switch see the hp-ux server, EVA 4000 and msl...
MSL can see only EVA 4000, and hp-ux server can see only EVA...
what i need to do , that hp-ux will see msl, and msl will see hp-ux???
Azamat
Frequent Advisor

Re: MSL 6030 and Network Storage Router e1200-160

has anybody here???
IBaltay
Honored Contributor

Re: MSL 6030 and Network Storage Router e1200-160

Hi,
in my opinion it is much better to do the zonning:
a) if you have the storage, then the HPUX host separately with the storage
b) and then the HPUX host separately with the library

This will isolate the host/tape and host/san drive communication and everything will be in its right place
the pain is one part of the reality
Torsten.
Acclaimed Contributor

Re: MSL 6030 and Network Storage Router e1200-160

Let's check your mapping first.

Telnet to the NSR and log on (root/password).

Then do

1) Perform Configuration

5) Device Mapping

2) Display Current Map

and post the output.


Also attach the output of

# ioscan -fn

from your hp-ux server.

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Miguel Carranza
Frequent Advisor

Re: MSL 6030 and Network Storage Router e1200-160

I am having a similar problem. Replaced the router in the library. got a refurbished one from ebay. My switch zoning "sees" the wwn from the router, and the zoning seems to be working, but my windows server still dont see the library. Any ideas?
Azamat
Frequent Advisor

Re: MSL 6030 and Network Storage Router e1200-160

Hi, Miguel
first thing that you should do is create new LUN`s for your M$ Win server.

b.r., Azamat
raghu189
New Member

Re: MSL 6030 and Network Storage Router e1200-160

Hi Azamat,

what was solutiom for you problem with NSR.

Do send as I am also facing same issue...