- Community Home
- >
- Storage
- >
- Midrange and Enterprise Storage
- >
- StoreVirtual Storage
- >
- Re: Configuring network traffic types of VSA in CM...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-06-2017 01:54 AM
тАО06-06-2017 01:54 AM
Configuring network traffic types of VSA in CMC
We have a small 2-node cluster with StoreVirtual VSA (Quorum witness on a QNAP NAS).
The VSA has eth0 connected to the management network and eth1 to the iSCSI network.
All iSCSI traffic is isolated on 2x 10GbE NICs.
Apart from some latency issues the system is up and running.
But I recently discovered that the network confguration in CMC is not quite right.
When I goto Network->Comminication all network types are assigned to eth1.
(And the manager IP addressses shown below are the iSCSI assigned addresses.)
I would like to change the management interface to eth0, but can I do this on a live system?
Since the Quorum witness is on the management LAN, I guess I should also change the Lefthand OS NIC to eth0, but again: is this possible on a live system?
How will the nodes communicate with each other when I change the Lefthand OS NIC on the first VSA and then the other?
After changing this I should run "Update manager IP addresses" - correct?
Any help appriciated.
TIA
Kristian
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-05-2018 05:12 AM
тАО06-05-2018 05:12 AM
Re: Configuring network traffic types of VSA in CMC
Hello Kristian,
I have the exact same pb (2 nodes cluster, all network types on eth1, latency issues).
Did you get any answers ? How did you proceed ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-21-2018 01:42 AM - edited тАО06-21-2018 03:48 AM
тАО06-21-2018 01:42 AM - edited тАО06-21-2018 03:48 AM
Re: Configuring network traffic types of VSA in CMC
Dear @conXO
You may change only the management interface to eth0, this does not require any downtime. Lefthand OS NIC (will still maintain the quorum) and iSCSI should remain at eth1.
"When configuring a management interface on an HP StoreVirtual Storage system, you must designate the storage interface (iSCSI) as the LeftHand OS interface for that storage system in the CMC. This is done on the communications tab in the network configuration category for that storage system."
You can also refer the best practices:
https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-c04855000
This blog, although not exactly as your situation but, gives a general idea:
http://adminhelpline.blogspot.com/2016/06/hpe-storevirtual-network-configuration.html
Regarding latency issue, you may disable ATS Heartbeat, Large receive offload (LRO - Root access required) and delayed ACK.
HPE StoreVirtual 4000 and HPE StoreVirtual 3000 Storage - Host Performance And Connectivity May Become Degraded When Running VMware ESXi 5.5 Update 2 Or Later:
https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-a00009136en_us
Hope this helps.
Regards,
Vikas
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-25-2018 05:22 AM
тАО06-25-2018 05:22 AM
Re: Configuring network traffic types of VSA in CMC
Thanks Vikas,
I will lok into your suggestions.
Regards
Kristian