- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: Wake on LAN not working
Switches, Hubs, and Modems
1823921
Members
3032
Online
109667
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Forums
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-11-2011 07:36 PM
05-11-2011 07:36 PM
Wake on LAN not working
Hi,
I have setup a small networking connect 2 PCs to a Procurve 2610 to test out WoL.
I have turned on BIOS WOL for both PCs and make sure they can ping each other. I also checked the NIC, WOL Setting is set to Magic packet. SolarWinds WOL is installed on PC1.
I shutdown PC2, use Solarwinds WOL on PC1 to intiate WOL with the MAC and IP of PC2.
Unfortunately I do not see any WOL packets on my PC1 Wiresharks, PC2 did not wake at all.
There is no ARP entry for PC2 in the switch (After PC2 is being turned off).
Please help!!
I have setup a small networking connect 2 PCs to a Procurve 2610 to test out WoL.
I have turned on BIOS WOL for both PCs and make sure they can ping each other. I also checked the NIC, WOL Setting is set to Magic packet. SolarWinds WOL is installed on PC1.
I shutdown PC2, use Solarwinds WOL on PC1 to intiate WOL with the MAC and IP of PC2.
Unfortunately I do not see any WOL packets on my PC1 Wiresharks, PC2 did not wake at all.
There is no ARP entry for PC2 in the switch (After PC2 is being turned off).
Please help!!
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-11-2011 09:32 PM
05-11-2011 09:32 PM
Re: Wake on LAN not working
Thanks, problem resolved. I could wake the PC. Just that Wiresharks does not show WOL packets
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-03-2011 10:46 PM
07-03-2011 10:46 PM
Re: Wake on LAN not working
How did you configure the Wake-on-LAN on the 2610
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
Company
Learn About
News and Events
Support
© Copyright 2025 Hewlett Packard Enterprise Development LP