- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Aruba & ProVision-based
- >
- Re: HP 2920: Ubiquiti and PoE concerns
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-17-2016 07:00 PM - edited 02-17-2016 07:30 PM
02-17-2016 07:00 PM - edited 02-17-2016 07:30 PM
Hello,
I seem to have encountered an odd situation in our test lab.
I've managed to get our Ubiquiti Nanobeam 5AC antenna, up and running, from an unmanaged switch (HP 2524) and through its bundled PoE injector. Executing ping command indicates that the antenna is in our LAN.
However, when connected to a managed switch (HP 2920), the antenna is not seen on the network, though the configuration cites that it is truncated to trk1 and the port is tagged to the appropriate VLAN. LED on the antenna also indicates the antenna is already up.
Any idea why is this so?
Regards,
Bar
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-17-2016 11:58 PM
02-17-2016 11:58 PM
Re: HP 2920: Ubiquiti and PoE concerns
Double check if the appropriate VLAN should be UNtagged, just like on the unmanaged switch.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-18-2016 12:36 AM - edited 02-18-2016 12:41 AM
02-18-2016 12:36 AM - edited 02-18-2016 12:41 AM
Re: HP 2920: Ubiquiti and PoE concerns
Done that.
J9729A_OLC(config)# sh vlan 4 Status and Counters - VLAN Information - VLAN 4 VLAN ID : 4 Name : nanobeamTest Status : Port-based Voice : No Jumbo : No Port Information Mode Unknown VLAN Status ---------------- -------- ------------ ---------- 17 Untagged Learn Down 45 Untagged Learn Down Trk1 Tagged Learn Up
Antenna is connected to port 17 through its PoE injector but still status is "down". However, testing it out in the field, i.e., outside our test lab, yields good connectivity.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-10-2016 08:11 PM