- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: All blades offline in c3000
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-25-2013 06:28 PM
тАО07-25-2013 06:28 PM
All blades offline in c3000
Hi guys,
We just had an issue in which all of our blades had a red X and status unknown in our c3000 enclosure.
OA Firmware 3.6
Any ideas? Log is below
Jul 26 05:45:44 Kernel: hub 1-1:1.0: over-current change on port 2
Jul 26 05:45:44 Kernel: hub 1-1:1.0: over-current change on port 2
Jul 26 05:45:45 Kernel: hub 1-1:1.0: over-current change on port 2
Jul 26 05:45:45 Kernel: hub 1-1:1.0: over-current change on port 2
Jul 26 05:46:28 Kernel: Network link is up at 1000Mbps - Full Duplex
Jul 26 05:46:30 OA: Time zone changed to SGT-8
Jul 26 05:46:32 OA: LCD Status is: OK.
Jul 26 05:46:32 OA: Device 2 power delayed during device discovery.
Jul 26 05:46:33 OA: Blade in bay #2 status changed to OK
Jul 26 05:46:33 Enclosure-Link: Service started
Jul 26 05:46:40 Enclosure-Link: Initial topology scan completed successfully
Jul 26 05:46:42 OA: Device 2 power delayed until potential partner devices are discovered.
Jul 26 05:46:44 Redundancy: Service started (ACTIVE)
Jul 26 05:46:44 OA: Onboard Administrator booted successfully
Jul 26 05:46:57 OA: HTTP server is up
Jul 26 05:47:01 OA: VLAN is disabled
Jul 26 05:47:50 OA: Internal health status of interconnect in bay 1 changed to OK
Jul 26 05:49:38 OA: Management Processor on Blade 1 appears unresponsive.
Jul 26 05:49:43 OA: Partner device 2 was denied power because the corresponding device is missing.
Jul 26 05:49:56 OA: Management Processor on Blade 4 appears unresponsive.
Jul 26 05:50:20 OA: Management Processor on Blade 8 appears unresponsive.
Jul 26 05:51:52 OA: Blade 1 has been allocated a default power value of 509W because iLO appears unresponsive.
Jul 26 05:51:52 OA: Blade 4 has been allocated a default power value of 509W because iLO appears unresponsive.
Jul 26 05:51:52 OA: Blade 8 has been allocated a default power value of 509W because iLO appears unresponsive.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-25-2013 10:35 PM
тАО07-25-2013 10:35 PM
Re: All blades offline in c3000
I would first check and restart the OA, then the ILOs (blades) if needed.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-28-2013 04:07 PM
тАО07-28-2013 04:07 PM
Re: All blades offline in c3000
I did restart the OA but unfortunately this did not do anything for the blades.
I had to unplug the power on the enclosure, wait, then plug it back in.
Not sure if a newer firmware fixes this?