- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: BL460c on C7000 enclosure
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-14-2007 09:45 AM
тАО12-14-2007 09:45 AM
Windows 2003 R2 Standard Server SP2
HP NC373i Multifunction Gigabit Server Adapter
Driver Version HP 3.4.10.0
HP Network Configuration Utility
Version 8.80.0.12
Issue:
Speed/Duplex Setting is greyed out to AUTO/AUTO
I need it set to 100/FULL because our switch is Cisco Fast Ethernet and the server is unable to sense 100MB, the network state is down.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-14-2007 09:55 AM
тАО12-14-2007 09:55 AM
Re: BL460c on C7000 enclosure
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-14-2007 09:56 AM
тАО12-14-2007 09:56 AM
Re: BL460c on C7000 enclosure
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-14-2007 10:28 AM
тАО12-14-2007 10:28 AM
SolutionThe connection between the blade and the interconnect module is always gigabit (according to the manual, the wiring is actually equivalent to a _fibre_ gigabit interface).
If you're using blade switch interconnect modules, change the settings of the interconnect module: that's where the state of the external connection is managed.
If you're using an ethernet Pass-Thru module, then I must tell you those things are gigabit _only_. They cannot fall back to 100Mb speed.
See question 5:
http://h18004.www1.hp.com/products/blades/components/ethernet/pass-thru/questionsanswers.html#a5
See also the specifications:
http://h18004.www1.hp.com/products/blades/components/ethernet/pass-thru/specifications.html
"Full duplex 1Gb per port (no auto-negotiation)".
MK
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-12-2008 12:33 AM
тАО03-12-2008 12:33 AM
Re: BL460c on C7000 enclosure
I have the same question about adjust NIC speed.
Does OA make NIC speed unmodifiable ?
If I config CISCO 3020 or GbE2 downlink port speed to 100/full , what will happen next ?
Regards.
Terence