- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: c7000 ebipa blade ilo config
BladeSystem - General
1757002
Members
2289
Online
108858
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
The article you are trying to access is permanently deleted.
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-25-2007 07:04 PM
тАО08-25-2007 07:04 PM
c7000 ebipa blade ilo config
Is it correct that the ip of the OA and the ebipa ips for the blades and interconnects must be on the same subnet for OA to be able to open up a console? I have tested it both ways and I can manage them if they are all on the same subnet with OA but not if they are different.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-26-2007 06:20 PM
тАО08-26-2007 06:20 PM
Re: c7000 ebipa blade ilo config
When a server blade or interconnect module is inserted into a bay that has EBIPA
enabled, that management port will get the specific static IP address from the Onboard
Administrator if that device is configured for DHCP. This is only possible when they are in the Same Subnet. I dont think otherwise is possible, If so, Ideas are most welcome.
Regards,
James.
enabled, that management port will get the specific static IP address from the Onboard
Administrator if that device is configured for DHCP. This is only possible when they are in the Same Subnet. I dont think otherwise is possible, If so, Ideas are most welcome.
Regards,
James.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-26-2007 11:22 PM
тАО08-26-2007 11:22 PM
Re: c7000 ebipa blade ilo config
thanks I figured so but wanted to make sure as it calls for me to eat up 16 more ip's off our utility network per say.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP